Nissan Qashqai (2007-2010). Manual — part 1046
REAR DOOR LOCK
DLK-263
< ON-VEHICLE REPAIR >
[WITH I-KEY, WITHOUT SUPER LOCK]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
6.
While pulling the outside handle, remove the door key cylinder
assembly.
7.
While pulling the outside handle, slide toward rear of vehicle to
remove the outside handle.
8.
Remove the front gasket and the rear gasket.
9.
Remove the door lock assembly mounting bolts (TORX: T30).
10. Disconnect the door lock actuator connector, and then remove
the door lock assembly.
11. While pulling the outside handle bracket, slide toward rear of
vehicle to remove the outside handle bracket.
PIIB5809E
JMKIA0524ZZ
PIIB5811E
MIIB0633E
PIIB5814E
DLK-264
< ON-VEHICLE REPAIR >
[WITH I-KEY, WITHOUT SUPER LOCK]
REAR DOOR LOCK
12. Reach in to separate the outside handle cable connection.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• To install each rod, rotate the rod holder until a click is felt.
• Check the door lock/unlock operation after installation.
• Check the door open/close operation after installation.
INSIDE HANDLE
INSIDE HANDLE : Exploded View
INFOID:0000000001091311
INSIDE HANDLE : Removal and Installation
INFOID:0000000001091312
REMOVAL
1.
Remove the rear door finisher. Refer to
INT-13, "REAR DOOR FINISHER : Removal and Installation"
.
2.
Remove the door sealing screen.
PIIB5815E
1.
Outside handle
2.
Outside handle escutcheon
3.
Front gasket
4.
Rear gasket
5.
Outside handle bracket
6.
Inside handle
7.
Door lock assembly
Refer to
for symbols in the figure.
JMKIA0189GB
REAR DOOR LOCK
DLK-265
< ON-VEHICLE REPAIR >
[WITH I-KEY, WITHOUT SUPER LOCK]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
3.
Remove the inside handle mounting bolt, and then disconnect the inside handle knob cable and the lock
knob cable.
4.
Remove the inside handle.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Check the door lock/unlock operation after installation.
• Check the door open/close operation after installation.
OUTSIDE HANDLE
OUTSIDE HANDLE : Exploded View
INFOID:0000000001091313
OUTSIDE HANDLE : Removal and Installation
INFOID:0000000001091314
REMOVAL
1.
Remove the rear door finisher. Refer to
INT-13, "REAR DOOR FINISHER : Removal and Installation"
.
2.
Fully close the front door window.
3.
Remove the door sealing screen.
4.
Remove the inside handle mounting bolt, disconnect the inside handle knob cable and the lock knob
cable.
1.
Outside handle
2.
Outside handle escutcheon
3.
Front gasket
4.
Rear gasket
5.
Outside handle bracket
6.
Inside handle
7.
Door lock assembly
Refer to
JMKIA0189GB
DLK-266
< ON-VEHICLE REPAIR >
[WITH I-KEY, WITHOUT SUPER LOCK]
REAR DOOR LOCK
5.
Remove the door side grommet, and remove the door key cylin-
der assembly (driver side) and the outside handle escutcheon
(passenger side) mounting bolts from the grommet hole.
CAUTION:
Do not forcibly remove the bolts (TORX: T10).
6.
While pulling the outside handle, and then remove the door key
cylinder assembly.
7.
While pulling the outside handle, slide toward rear of vehicle to
remove the outside handle.
8.
Remove the front gasket and the rear gasket.
9.
While pulling the outside handle bracket, slide toward rear of
vehicle to remove the outside handle bracket.
JMKIA0020ZZ
PIIB5809E
JMKIA0524ZZ
PIIB5811E
PIIB5814E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст