Nissan Qashqai (2007-2010). Manual — part 194
ASCD BRAKE SWITCH
EC-295
< COMPONENT DIAGNOSIS >
[HR16DE (WITH EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
8.
CHECK INTERMITTENT INCIDENT
GI-39, "Intermittent Incident"
.
>> INSPECTION END
Component Inspection (ASCD Brake Switch)
INFOID:0000000001056490
1.
CHECK ASCD BRAKE SWITCH-I
1.
Turn ignition switch OFF.
2.
Disconnect ASCD brake switch harness connector.
3.
Check the continuity between ASCD brake switch terminals under the following conditions.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> GO TO 2.
2.
CHECK ASCD BRAKE SWITCH-II
1.
Adjust ASCD brake switch installation. Refer to
BR-17, "Removal and Installation"
(LHD) or
2.
Check the continuity between ASCD brake switch terminals under the following conditions.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace ASCD brake switch.
Component Inspection (ASCD Clutch Switch)
INFOID:0000000001056491
1.
CHECK ASCD CLUTCH SWITCH-I
1.
Turn ignition switch OFF.
2.
Disconnect ASCD clutch switch harness connector.
3.
Check the continuity between ASCD clutch switch terminals under the following conditions.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> GO TO 2.
2.
CHECK ASCD CLUTCH SWITCH-II
1.
Adjust ASCD clutch switch installation. Refer to
CL-8, "Removal and Installation"
2.
Check the continuity between ASCD clutch switch terminals under the following conditions.
Terminals
Condition
Continuity
1 and 2
Brake pedal
Fully released
Existed
Slightly depressed
Not existed
Terminals
Condition
Continuity
1 and 2
Brake pedal
Fully released
Existed
Slightly depressed
Not existed
Terminals
Condition
Continuity
1 and 2
Clutch pedal
Fully released
Existed
Slightly depressed
Not existed
Terminals
Condition
Continuity
1 and 2
Clutch pedal
Fully released
Existed
Slightly depressed
Not existed
EC-296
< COMPONENT DIAGNOSIS >
[HR16DE (WITH EURO-OBD)]
ASCD BRAKE SWITCH
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace ASCD clutch switch.
ASCD INDICATOR
EC-297
< COMPONENT DIAGNOSIS >
[HR16DE (WITH EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
ASCD INDICATOR
Description
INFOID:0000000001056492
ASCD indicator lamp illuminates to indicate ASCD operation status. Lamp has two indicators, CRUISE and
SET, and is integrated in combination meter.
CRUISE lamp illuminates when MAIN switch on ASCD steering switch is turned ON to indicated that ASCD
system is ready for operation.
SET lamp illuminates when following conditions are met.
• CRUISE lamp is illuminated.
• SET/COAST switch on ASCD steering switch is turned ON while vehicle speed is within the range of ASCD
setting.
SET lamp remains lit during ASCD control.
Refer to
for the ASCD function.
Component Function Check
INFOID:0000000001056493
1.
ASCD INDICATOR FUNCTION
Check ASCD indicator under the following conditions.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Go to
Diagnosis Procedure
INFOID:0000000001056494
1.
CHECK DTC
Check that DTC U1001 is not displayed.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Perform trouble diagnosis for DTC U1001. Refer to
.
2.
CHECK COMBINATION METER OPERATION
MWI-23, "CONSULT-III Function (METER/M&A)"
.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Check combination meter circuit. Refer to
MWI-43, "Wiring Diagram - METER -"
.
3.
CHECK INTERMITTENT INCIDENT
GI-39, "Intermittent Incident"
.
>> INSPECTION END
ASCD INDICATOR
CONDITION
SPECIFICATION
CRUISE LAMP
• Ignition switch: ON
• MAIN switch: Pressed at the
1st time
→
at the 2nd time
ON
→
OFF
SET LAMP
• MAIN switch: ON
• When vehicle speed: Be-
tween 40 km/h (25 MPH) and
144 km/h (89 MPH)
• ASCD: Operating
ON
• ASCD: Not operating
OFF
EC-298
< COMPONENT DIAGNOSIS >
[HR16DE (WITH EURO-OBD)]
COOLING FAN
COOLING FAN
Description
INFOID:0000000001056495
Cooling fan operates at low and high speed when the current flows in the cooling fan motor.
Refer to
for cooling fan operation.
Component Function Check
INFOID:0000000001056496
1.
CHECK COOLING FAN LOW SPEED FUNCTION
With CONSULT-III
1.
Turn ignition switch ON.
2.
Perform “COOLING FAN” in “ACTIVE TEST” mode with CONSULT-III.
3.
Make sure that cooling fan operates at low and high speed.
Without CONSULT-III
1.
Perform IPDM E/R auto active test and check cooling fan motor operation, refer to
.
2.
Make sure that cooling fan operates at low and high speed.
Is the inspection result normal?
YES
>> INSPECTION END.
NO
>> Go to
Diagnosis Procedure
INFOID:0000000001056497
1.
CHECK IPDM E/R POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect IPDM E/R harness connector E14.
3.
Check the voltage between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair open circuit or short to ground or short to power in harness or connectors
2.
CHECK COOLING FAN MOTOR CIRCUIT FOR OPEN AND SHORT
1.
Turn ignition switch OFF.
2.
Disconnect cooling fan motor harness connector.
3.
Check the continuity between cooling fan motor harness connector and IPDM E/R harness connector.
4.
Check the continuity between cooling fan motor harness connector and ground.
5.
Also check harness for short to ground and short to power.
Is the inspection result normal?
IPDM E/R
Ground
Voltage
Connector
Terminal
E14
53
Ground
Battery voltage
Cooling fan motor
IPDM E/R
Continuity
Connector
Terminal
Connector
Terminal
E3
1
E14
52
Existed
54
Cooling fan motor
IPDM/ER
Ground
Continuity
Connector
Terminal
Connector
Terminal
E3
2
E10
5
Ground
Existed
6
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст