Nissan Qashqai (2007-2010). Manual — part 1450
WIPER AND WASHER SYSTEM SYMPTOMS
WW-91
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
Rear wiper does not
stop.
ON only
• Combination switch
• BCM
Rear wiper motor circuit
Refer to
.
INT only
• Combination switch
• BCM
Combination switch
Refer to
Rear wiper does not
operate normally.
Wiper is not linked to
the washer operation.
• Combination switch
• Harness between rear wiper motor and BCM
• BCM
Combination switch
Refer to
BCM
—
Rear wiper does not
return to the Stop posi-
tion (Stops after a five-
second operation).
• BCM
• Harness between rear wiper motor and BCM
• Rear wiper motor
Rear wiper auto stop signal
circuit
Refer to
.
Rear wiper stops after
operating for five sec-
onds when ignition
switch is turned ON.
Rear wiper does not
operate even when se-
lector lever is shifted to
the “R”.
Reverse switch signal (CAN communication)
• BCM
• IPDM E/R
IPDM E/R DATA MONITOR
“REV SW”
Headlamp washer
does not operate.
Headlamp washer
does not operate with
the front washer when
headlamps are turned
ON.
• Combination switch
• Harness between combination switch and BCM
• BCM
• Headlamp washer pump
Combination switch
Refer to
• Fusible link
• Harness between fusible link and headlamp
washer relay
• Headlamp washer relay
• Harness between headlamp washer relay and
IPDM E/R
• IPDM E/R
• Harness between headlamp washer relay and
headlamp washer pump
• Harness between headlamp washer pump and
ground
• Headlamp washer pump
Headlamp washer circuit
Refer to
.
BCM
—
Symptom
Probable malfunction location
Inspection item
WW-92
< SYMPTOM DIAGNOSIS >
NORMAL OPERATING CONDITION
NORMAL OPERATING CONDITION
Description
INFOID:0000000000924458
FRONT WIPER MOTOR PROTECTION FUNCTION
• IPDM E/R may stop the front wiper to protect the front wiper motor if any obstruction (operation resistance)
such as a large amount of snow is detected during the front wiper operation.
• At that time turn OFF the front wiper and remove the foreign object. Then wait for approximately 20 seconds
or more and reactivate the front wiper. The wiper will operate normally.
REAR WIPER MOTOR PROTECTION FUNCTION
• BCM may stop rear wiper to protect the rear wiper motor when the rear wiper is stopped for 5 seconds or
more due to a snowfall.
• Rear wiper operates normally one minute after the obstacles are removed with rear wiper OFF.
FRONT WIPER DOES NOT OPERATE
WW-93
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
FRONT WIPER DOES NOT OPERATE
Description
INFOID:0000000000924456
The front wiper does not operate under any operation conditions.
Diagnosis Procedure
INFOID:0000000000924457
1.
CHECK WIPER RELAY OPERATION
IPDM E/R AUTO ACTIVE TEST
1.
Start IPDM E/R auto active test. Refer to
PCS-9, "Diagnosis Description"
.
2.
Check that the front wiper operates at the LO/HI operation.
CONSULT-III ACTIVE TEST
1.
Select "FRONT WIPER" of IPDM E/R active test item.
2.
With operating the test item, check front wiper operation.
Is front wiper operation normally?
YES
>> GO TO 5.
NO
>> GO TO 2.
2.
CHECK FRONT WIPER MOTOR FUSE
1.
Turn the ignition switch OFF.
2.
Check that the front wiper motor 30A fuse (#44) is not fusing.
Is the fuse fusing?
YES
>> Replace the fuse after repairing the applicable circuit.
NO
>> GO TO 3.
3.
CHECK FRONT WIPER MOTOR GROUND OPEN CIRCUIT
1.
Disconnect front wiper motor connector.
2.
Check continuity between front wiper motor harness connector and ground.
Does continuity exist?
YES
>> GO TO 4.
NO
>> Repair the harnesses or connectors.
4.
CHECK FRONT WIPER MOTOR OUTPUT VOLTAGE
CONSULT-III ACTIVE TEST
1.
Disconnect front wiper motor connector.
2.
Turn the ignition switch ON.
3.
Select "FRONT WIPER" of IPDM E/R active test item.
4.
With operating the test item, check voltage between IPDM E/R harness connector and ground.
LO
: Front wiper LO operation
HI
: Front wiper HI operation
OFF
: Stop the front wiper.
Front wiper motor
Ground
Continuity
Connector
Terminal
E20
5
Existed
WW-94
< SYMPTOM DIAGNOSIS >
FRONT WIPER DOES NOT OPERATE
Is the measurement value normal?
YES
>> Replace front wiper motor.
NO
>> Replace IPDM E/R.
5.
CHECK FRONT WIPER REQUEST SIGNAL INPUT
CONSULT-III DATA MONITOR
1.
Select "FR WIP REQ" of IPDM E/R data monitor item.
2.
Switch the front wiper switch to HI and LO.
3.
With operating the front wiper switch, check the status of "FR WIP REQ".
Is the status of item normal?
YES
>> Replace IPDM E/R.
NO
>> GO TO 6.
6.
CHECK COMBINATION SWITCH
1.
Perform the inspection of the combination switch. Refer to
Is combination switch normal?
YES
>> Replace BCM. Refer to
NO
>> Repair or replace the applicable parts.
Terminals
Test item
Voltage
(Approx.)
(+)
(
−
)
IPDM E/R
Ground
FRONT WIP-
ER
Connector
Terminal
E10
7
LO
Battery
voltage
OFF
0 V
8
HI
Battery
voltage
OFF
0 V
Monitor item
Condition
Monitor
status
FR WIP REQ
Front wiper switch HI
ON
HI
OFF
STOP
Front wiper switch LO
ON
LOW
OFF
STOP
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст