Nissan Qashqai (2007-2010). Manual — part 713
BRC-50
< COMPONENT DIAGNOSIS >
[ABS]
BRAKE WARNING LAMP
BRAKE WARNING LAMP
Description
INFOID:0000000000925063
×
: ON –: OFF
NOTE:
• 1: Brake warning lamp will turn on in case of parking brake operation (when switch is ON) or of brake fluid level switch operation
(when brake fluid is insufficient).
• 2: After starting engine, brake warning lamp is turned off.
Component Function Check
INFOID:0000000000925064
1.
BRAKE WARNING LAMP OPERATION CHECK 1
Check that the lamp illuminates for approximately 1 second after the ignition switch is turned ON.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Go to diagnosis procedure. Refer to
2.
BRAKE WARNING LAMP OPERATION CHECK 2
Check that the brake warning lamp in the combination meter turns ON/OFF correctly when operating the park-
ing brake pedal.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Check parking brake switch. Refer to
.
Diagnosis Procedure
INFOID:0000000000925065
1.
CHECK PARKING BRAKE SWITCH
Check that the brake warning lamp in the combination meter turns ON/OFF correctly when operating the park-
ing brake pedal.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Check parking brake switch. Refer to
.
2.
CHECK SELF-DIAGNOSIS
Perform ABS actuator and electric unit (control unit) self-diagnosis.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Check items displayed by self-diagnosis.
3.
CHECK COMBINATION METER
Check if the indication and operation of combination meter are normal. Refer to
.
Is the inspection result normal?
YES
>> Replace ABS actuator and electric unit (control unit).
NO
>> Repair or replace combination meter.
Condition
Brake warning lamp
NOTE 1
Ignition switch OFF
–
For 1 second after turning ON ignition switch
×
NOTE 2
1 second later after turning ON ignition switch
×
NOTE 2
EBD function is malfunctioning.
×
ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
BRC-51
< ECU DIAGNOSIS >
[ABS]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
ECU DIAGNOSIS
ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
Reference Value
INFOID:0000000000925072
VALUES ON THE DIAGNOSIS TOOL
CAUTION:
The display shows the control unit calculation data, so a normal value might be displayed even in the
event the output circuit (harness) is open or short-circuited.
Monitor item
Condition
Value/Status
FR LH SENSOR
Wheel speed
Vehicle stopped
0 [km/h (MPH)]
Vehicle running
NOTE 1
Nearly matches the
speed meter display
(
±
10% or less)
FR RH SENSOR
Wheel speed
Vehicle stopped
0 [km/h (MPH)]
Vehicle running
NOTE 1
Nearly matches the
speed meter display
(
±
10% or less)
RR LH SENSOR
Wheel speed
Vehicle stopped
0 [km/h (MPH)]
Vehicle running
NOTE 1
Nearly matches the
speed meter display
(
±
10% or less)
RR RH SENSOR
Wheel speed
Vehicle stopped
0 [km/h (MPH)]
Vehicle running
NOTE 1
Nearly matches the
speed meter display
(
±
10% or less)
STOP LAMP SW
Stop lamp switch signal status
When brake pedal is depressed
On
When brake pedal is not depressed
Off
BATTERY VOLT
Battery voltage supplied to the ABS actuator
and electric unit (control unit)
Ignition switch ON
10 – 16 V
DECEL G SENSOR
NOTE 2
Decel G detected by decel G sensor
Vehicle on level surface or on slope
According to gradi-
ent of slope
FR RH IN SOL
Operation status of front RH inlet solenoid
valve
Actuator (solenoid valve) is active (“AC-
TIVE TEST” with CONSULT-III) or actu-
ator relay is inactive (in fail-safe mode)
On
When the actuator (solenoid valve) is
not active and actuator relay is active
(ignition switch ON)
Off
FR RH OUT SOL
Operation status of front RH outlet solenoid
valve
Actuator (solenoid valve) is active (“AC-
TIVE TEST” with CONSULT-III) or actu-
ator relay is inactive (in fail-safe mode)
On
When the actuator (solenoid valve) is
not active and actuator relay is active
(ignition switch ON)
Off
FR LH IN SOL
Operation status of front LH inlet solenoid
valve
Actuator (solenoid valve) is active (“AC-
TIVE TEST” with CONSULT-III) or actu-
ator relay is inactive (in fail-safe mode)
On
When the actuator (solenoid valve) is
not active and actuator relay is active
(ignition switch ON)
Off
BRC-52
< ECU DIAGNOSIS >
[ABS]
ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
NOTE:
• 1: Confirm tire pressure is normal.
• 2: Only 4WD models.
• 3: Every 20 seconds momentary switch to OFF.
• 4: On and off timing for warning lamp and indicator lamp. Refer to
Wiring Diagram - BRAKE CONTROL SYSTEM -
INFOID:0000000000925073
FR LH OUT SOL
Operation status of front LH outlet solenoid
valve
Actuator (solenoid valve) is active (“AC-
TIVE TEST” with CONSULT-III) or actu-
ator relay is inactive (in fail-safe mode)
On
When the actuator (solenoid valve) is
not active and actuator relay is active
(ignition switch ON)
Off
RR RH IN SOL
Operation status of rear RH inlet solenoid
valve
Actuator (solenoid valve) is active (“AC-
TIVE TEST” with CONSULT-III) or actu-
ator relay is inactive (in fail-safe mode)
On
When the actuator (solenoid valve) is
not active and actuator relay is active
(ignition switch ON)
Off
RR RH OUT SOL
Operation status of rear RH outlet solenoid
valve
Actuator (solenoid valve) is active (“AC-
TIVE TEST” with CONSULT-III) or actu-
ator relay is inactive (in fail-safe mode)
On
When the actuator (solenoid valve) is
not active and actuator relay is active
(ignition switch ON)
Off
RR LH IN SOL
Operation status of rear LH inlet solenoid
valve
Actuator (solenoid valve) is active (“AC-
TIVE TEST” with CONSULT-III) or actu-
ator relay is inactive (in fail-safe mode)
On
When the actuator (solenoid valve) is
not active and actuator relay is active
(ignition switch ON)
Off
RR LH OUT SOL
Operation status of rear LH outlet solenoid
valve
Actuator (solenoid valve) is active (“AC-
TIVE TEST” with CONSULT-III) or actu-
ator relay is inactive (in fail-safe mode)
On
When the actuator (solenoid valve) is
not active and actuator relay is active
(ignition switch ON)
Off
MOTOR RELAY
Motor and motor relay operation
When the motor relay and motor are op-
erating
On
When the motor relay and motor are not
operating
Off
ACTUATOR RLY
NOTE 3
Actuator relay operation
When the actuator relay is operating
On
When the actuator relay is not operating
Off
ABS WARN LAMP
ABS warning lamp
NOTE 4
When ABS warning lamp is ON
On
When ABS warning lamp is OFF
Off
EBD SIGNAL
EBD operation
EBD is active
On
EBD is inactive
Off
ABS SIGNAL
ABS operation
ABS is active
On
ABS is inactive
Off
EBD FAIL SIG
EBD fail-safe signal
In EBD fail-safe
On
EBD is normal
Off
ABS FAIL SIG
ABS fail-safe signal
In ABS fail-safe
On
ABS is normal
Off
Monitor item
Condition
Value/Status
ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
BRC-53
< ECU DIAGNOSIS >
[ABS]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
JCFWA0031GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст