Nissan Qashqai (2007-2010). Manual — part 870
HA-50
< ON-VEHICLE REPAIR >
[AUTOMATIC AIR CONDITIONER (HR/MR)]
CONDENSER
12. Release radiator maintaining pawls, then pull-up the condenser assembly to release it from radiator. Refer
to
CO-13, "Removal and Installation"
(HR engine models) or
CO-35, "Removal and Installation"
(MR
engine models).
13. Maintain radiator pushing back.
14. Pull upward to remove condenser.
CAUTION:
Take care do not damaged condenser or radiator.
INSTALLATION
Installation is basically the reverse order of removal.
CAUTION:
• Replace O-rings of high-pressure flexible hose and high-pressure pipe 1 with new ones, and then
apply compressor oil to it when installing it.
• Female-side piping connection is thin and easy to deform. Slowly insert the male-side piping
straight in axial direction.
• Insert piping securely until a click is heard.
• After piping connection is completed, pull male-side piping by hand to make sure that connection
does not come loose.
• When recharging refrigerant, check for leaks.
LIQUID TANK
HA-51
< ON-VEHICLE REPAIR >
[AUTOMATIC AIR CONDITIONER (HR/MR)]
C
D
E
F
G
H
J
K
L
M
A
B
HA
N
O
P
LIQUID TANK
Exploded View
INFOID:0000000001093798
Removal and Installation
INFOID:0000000001093799
REMOVAL
1.
Use a refrigerant collecting equipment (for HFC-134a) to discharge the refrigerant.
2.
Remove engine cover ornament. Refer to
(MR engine models).
3.
Clean liquid tank and its surrounding area, and remove dust and rust from liquid tank.
CAUTION:
Be sure to clean carefully.
4.
Disconnect refrigerant sensor harness connector. Refer to
HA-52, "Removal and Installation"
5.
Remove liquid tank bracket support mounting screws (B).
6.
Remove high pressure pipe 1 (1) mounting bolt (A) from liquid
tank. Refer to
HA-45, "Removal and Installation"
.
7.
Remove liquid tank high pressure pipe mounting bolt (A) from
condenser.
8.
Remove liquid tank pipe bracket fixing screw.
CAUTION:
Cap or wrap the joint of high pressure pipe, liquid tank
pipes and condenser with suitable material such as vinyl
tape to avoid the entry of air.
9.
Remove liquid tank assembly.
INSTALLATION
Install liquid tank, and then install liquid tank bracket on condenser.
CAUTION:
• Make sure liquid tank bracket is securely installed at protrusion of condenser. (Make sure liquid tank
bracket does not move to a position below center of liquid tank.)
• Replace O-rings of A/C piping with new ones, and then apply compressor oil to it when installing it.
• When recharging refrigerant, check for leaks.
1.
Refrigerant pressure sensor
2.
O-ring
3.
Liquid tank bracket
4.
Liquid tank
5.
Condenser
6.
Liquid tank fixing screw
7.
Liquid tank pipe fixing bolt
E1KIA0050GB
E1KIA0068ZZ
HA-52
< ON-VEHICLE REPAIR >
[AUTOMATIC AIR CONDITIONER (HR/MR)]
REFRIGERANT PRESSURE SENSOR
REFRIGERANT PRESSURE SENSOR
Exploded View
INFOID:0000000001093800
Removal and Installation
INFOID:0000000001093801
REMOVAL
1.
Remove liquid tank. Refer to
.
2.
Fix the liquid tank (1) with a vise (A). Remove the refrigerant
pressure sensor (2) with a wrench (B).
CAUTION:
Be careful not to damage liquid tank.
INSTALLATION
Installation is basically the reverse order of removal.
CAUTION:
• Apply compressor oil to O-ring of refrigerant pressure sensor when installing it.
• When recharging refrigerant, check for leaks.
1.
Refrigerant pressure sensor
2.
O-ring
3.
Liquid tank bracket
4.
Liquid tank
5.
Condenser
6.
Liquid tank fixing screw
7.
Liquid tank pipe fixing bolt
E1KIA0050GB
JSIIA0075ZZ
EVAPORATOR
HA-53
< ON-VEHICLE REPAIR >
[AUTOMATIC AIR CONDITIONER (HR/MR)]
C
D
E
F
G
H
J
K
L
M
A
B
HA
N
O
P
EVAPORATOR
Exploded View
INFOID:0000000001093802
Removal and Installation
INFOID:0000000001093803
REMOVAL
1.
Remove low-pressure pipe 2 and high-pressure pipe 1 from expansion valve. Refer to
HA-45, "Removal and Installation"
CAUTION:
Cap or wrap the joint of expansion valve, low-pressure pipe 2 and high-pressure pipe 1 with suit-
able material such as vinyl tape to avoid the entry of air.
2.
Remove heater and cooling fixing clamp and hoses. Refer to
VTL-32, "Removal and Installation"
CO-13, "Removal and Installation"
(HR engine models) or
CO-35, "Removal and Installation"
models).
3.
Remove heater and cooling unit assembly. Refer to
VTL-32, "Removal and Installation"
.
4.
Remove evaporator cover fixing screws and cover. Refer to
HA-53, "Removal and Installation"
.
1.
Heater & blower unit assembly
2.
Heater & cooling unit assembly
3.
Evaporator
4.
O-ring
5.
Low pressure pipe 1 and high pres-
sure pipe 2 assembly
6.
Expansion valve
7.
Heater sealing
8.
Low pressure flexible hose and pipe
2
9.
Low pressure pipe 2 fixing clamp as-
sembly
10. High pressure flexible hose
11.
Compressor
12. Low pressure flexible hose
13. Low & high pipe bracket support
14. High pressure pipe 1
15. Condenser assembly
16. Liquid tank fixing bracket
17. Refrigerant pressure sensor
18. Liquid tank
E1KIA0037GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст