Nissan Pathfinder (2010 year). Instruction — part 147
DOOR REQUEST SWITCH
DLK-75
< COMPONENT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
2. Check voltage between Intelligent Key unit harness connector
M164 terminal 29 and ground.
Is the inspection result normal?
YES
>> Refer to
GI-37, "Intermittent Incident"
.
NO
>> Replace Intelligent Key unit. Refer to
SEC-118, "Removal and Installation"
BACK DOOR REQUEST SWITCH : Component Inspection
INFOID:0000000005259910
1.
CHECK BACK DOOR REQUEST SWITCH OPERATION
1. Turn ignition switch OFF.
2. Disconnect back door request switch connector.
3. Check continuity between back door request switch terminals 1
and 2.
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Replace back door request switch.
Connector
Item
Terminals
Condition
Voltage (V)
(Approx.)
(+)
(–)
M164
back door re-
quest switch
29
Ground
Back door re-
quest switch is
pressed
↓
Back door re-
quest switch is
released
0
↓
5
WIIA1183E
Component
Terminals
Condition
Continuity
Back door request
switch
1
2
Back door request
switch is pressed
Yes
Back door request
switch is released
No
WIIA1186E
2010 Pathfinder
DLK-76
< COMPONENT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
DOOR LOCK ACTUATOR
DOOR LOCK ACTUATOR
DRIVER SIDE
DRIVER SIDE : Description
INFOID:0000000005259911
Locks/unlocks the door with the signal from BCM.
DRIVER SIDE : Component Function Check
INFOID:0000000005259912
1.
CHECK FUNCTION
1. Use CONSULT-III to perform Active Test "DOOR LOCK".
2. Touch “ALL LOCK” or “ALL UNLOCK” to check that it works normally.
Is the inspection result normal?
YES
>> Door lock actuator is OK.
NO
>> Refer to
DLK-76, "DRIVER SIDE : Diagnosis Procedure"
DRIVER SIDE : Diagnosis Procedure
INFOID:0000000005259913
Regarding Wiring Diagram information, refer to
DLK-131, "Wiring Diagram — POWER DOOR LOCK SYS-
1.
CHECK DOOR LOCK ACTUATOR SIGNAL
1. Turn ignition switch OFF.
2. Check voltage between BCM connector M20 terminals 59, 65
and ground.
Is the inspection result normal?
YES
>> GO TO 2
NO
>> GO TO 3
2.
CHECK DOOR LOCK ACTUATOR HARNESS
1. Disconnect BCM and front door lock assembly LH (actuator).
2. Check continuity between BCM connector (A) M20 terminals 59,
65 and front door lock assembly LH (actuator) connector (B)
D14 terminals 1, 2.
Is the inspection result normal?
YES
>> Replace front door lock assembly LH (actuator).
Connector
Terminals
Condition
Voltage (V)
(Approx.)
(+)
(-)
M20
59
Ground
Driver door lock/unlock
switch is turned to UN-
LOCK
0
→
Battery voltage
65
Driver door lock/unlock
switch is turned to LOCK
0
→
Battery voltage
LIIA1046E
Connector
Terminals
Connector
Terminals
Continuity
M20
59
D14
2
Yes
65
1
ALKIA1191ZZ
2010 Pathfinder
DOOR LOCK ACTUATOR
DLK-77
< COMPONENT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
NO
>> Repair or replace harness.
3.
CHECK DOOR LOCK ACTUATOR HARNESS
1. Disconnect BCM and front door lock assembly LH (actuator).
2. Check continuity between BCM connector M20 terminals 59, 65
and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-59, "Removal and Installation"
NO
>> Repair or replace harness.
PASSENGER SIDE
PASSENGER SIDE : Description
INFOID:0000000005259914
Locks/unlocks the door with the signal from BCM.
PASSENGER SIDE : Component Function Check
INFOID:0000000005259915
1.
CHECK FUNCTION
1. Use CONSULT-III to perform Active Test DOOR LOCK.
2. Touch “ALL LOCK” or “ALL UNLOCK” to check that it works normally.
Is the inspection result normal?
YES
>> Door lock actuator is OK.
NO
>> Refer to
DLK-77, "PASSENGER SIDE : Diagnosis Procedure"
PASSENGER SIDE : Diagnosis Procedure
INFOID:0000000005259916
Regarding Wiring Diagram information, refer to
DLK-131, "Wiring Diagram — POWER DOOR LOCK SYS-
1.
CHECK FRONT DOOR LOCK ACTUATOR RH SIGNAL
1. Turn ignition switch OFF.
2. Check voltage between BCM connector M20 terminals 65, 66
and ground.
Is the inspection result normal?
YES
>> GO TO 2
Connector
Terminals
Continuity
M20
59
Ground
No
65
ALKIA0633ZZ
Connector
Terminals
Condition
Voltage (V)
(Approx.)
(+)
(-)
M20
65
Ground
Door lock/unlock switch is
turned to LOCK
0
→
Battery voltage
for 300 ms
66
Door lock/unlock switch is
turned to UNLOCK
LIIA1048E
2010 Pathfinder
DLK-78
< COMPONENT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
DOOR LOCK ACTUATOR
NO
>> GO TO 3
2.
CHECK DOOR LOCK ACTUATOR HARNESS
1. Disconnect BCM and front door lock actuator RH.
2. Check continuity between BCM connector (A) M20 terminals 65,
66 and front door lock actuator RH (B) D114 terminals 1, 2.
Is the inspection result normal?
YES
>> Replace front door lock actuator RH. Refer to
DLK-199, "Removal and Installation"
.
NO
>> Repair or replace harness.
3.
CHECK DOOR LOCK ACTUATOR HARNESS
1. Disconnect BCM and front door lock actuator RH.
2. Check continuity between BCM connector M19 terminals 65, 66
and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-59, "Removal and Installation"
NO
>> Repair or replace harness.
REAR LH
REAR LH : Description
INFOID:0000000005259917
Locks/unlocks the door with the signal from BCM.
REAR LH : Component Function Check
INFOID:0000000005259918
1.
CHECK FUNCTION
1. Use CONSULT-III to perform Active Test "DOOR LOCK".
2. Touch “ALL LOCK” or “ALL UNLOCK” to check that it works normally.
Is the inspection result normal?
YES
>> Door lock actuator is OK.
NO
>> Refer to
DLK-78, "REAR LH : Diagnosis Procedure"
.
REAR LH : Diagnosis Procedure
INFOID:0000000005259919
Regarding Wiring Diagram information, refer to
DLK-131, "Wiring Diagram — POWER DOOR LOCK SYS-
Terminal
Continuity
65
2
Yes
66
1
ALKIA1192ZZ
Terminals
Continuity
65
Ground
No
66
ALKIA0631ZZ
2010 Pathfinder
DOOR LOCK ACTUATOR
DLK-79
< COMPONENT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
1.
CHECK DOOR LOCK ACTUATOR SIGNAL
1. Turn ignition switch OFF.
2. Check voltage between BCM connector M20 terminals 65, 66
and ground.
Is the inspection result normal?
YES
>> GO TO 2
NO
>> GO TO 3
2.
CHECK DOOR LOCK ACTUATOR HARNESS
NOTE:
The passenger select unlock relay must remain connected during this test.
1. Disconnect BCM and rear door lock actuator LH.
2. Check continuity between BCM connector (A) M20 terminals 65,
66 and rear door lock actuator LH connector (B) D205 terminals
1, 2.
Is the inspection result normal?
YES
>> Replace rear door lock actuator LH.
NO
>> Repair or replace harness or passenger select unlock relay.
3.
CHECK DOOR LOCK ACTUATOR HARNESS
1. Disconnect BCM and each door lock actuator.
2. Check continuity between BCM connector M20 terminals 65, 66
and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-59, "Removal and Installation"
NO
>> Repair or replace harness or passenger select unlock relay.
REAR RH
Connector
Terminals
Condition
Voltage (V)
(Approx.)
(+)
(-)
M20
65
Ground
Door lock/unlock switch
is turned to LOCK
0
→
Battery voltage
for 300 ms
66
Door lock/unlock switch
is turned to UNLOCK
LIIA1048E
Terminals
Continuity
65
2
Yes
66
1
ALKIA1192ZZ
Terminals
Continuity
65
Ground
No
66
No
ALKIA0631ZZ
2010 Pathfinder
DLK-80
< COMPONENT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
DOOR LOCK ACTUATOR
REAR RH : Description
INFOID:0000000005259920
Locks/unlocks the door with the signal from BCM.
REAR RH : Component Function Check
INFOID:0000000005259921
1.
CHECK FUNCTION
1. Use CONSULT-III to perform Active Test "DOOR LOCK".
2. Touch “ALL LOCK” or “ALL UNLOCK” to check that it works normally.
Is the inspection result normal?
YES
>> Door lock actuator is OK.
NO
>> Refer to
DLK-80, "REAR RH : Diagnosis Procedure"
.
REAR RH : Diagnosis Procedure
INFOID:0000000005259922
Regarding Wiring Diagram information, refer to
DLK-131, "Wiring Diagram — POWER DOOR LOCK SYS-
1.
CHECK DOOR LOCK ACTUATOR SIGNAL
1. Turn ignition switch OFF.
2. Check voltage between BCM connector M20 terminals 65, 66
and ground.
Is the inspection result normal?
YES
>> GO TO 2
NO
>> GO TO 3
2.
CHECK DOOR LOCK ACTUATOR HARNESS
NOTE:
The passenger select unlock relay must remain connected during this test.
1. Disconnect BCM and rear door lock actuator RH.
2. Check continuity between BCM connector (A) M20 terminals 65,
66 and rear door lock actuator RH connector (B) D305 terminals
1, 2.
Is the inspection result normal?
YES
>> Replace rear door lock actuator RH.
NO
>> Repair or replace harness or passenger select unlock relay.
Connector
Terminals
Condition
Voltage (V)
(Approx.)
(+)
(-)
M20
65
Ground
Door lock/unlock switch
is turned to LOCK
0
→
Battery voltage
for 300 ms
66
Door lock/unlock switch
is turned to UNLOCK
LIIA1048E
Terminals
Continuity
65
2
Yes
66
1
ALKIA1192ZZ
2010 Pathfinder
DOOR LOCK ACTUATOR
DLK-81
< COMPONENT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
3.
CHECK DOOR LOCK ACTUATOR HARNESS
1. Disconnect BCM and rear door lock actuator RH.
2. Check continuity between BCM connector (A) M20 terminals 65,
66 and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-59, "Removal and Installation"
NO
>> Repair or replace harness or passenger select unlock relay.
BACK DOOR LATCH
BACK DOOR LATCH : Description
INFOID:0000000005259923
Locks/unlocks the door with the signal from BCM.
BACK DOOR LATCH : Diagnosis Procedure
INFOID:0000000005259924
Regarding Wiring Diagram information, refer to
DLK-131, "Wiring Diagram — POWER DOOR LOCK SYS-
1.
CHECK BACK DOOR LATCH SIGNAL
NOTE:
Ensure back door opener switch is operating properly before proceeding.
1. Turn ignition switch OFF.
2. Unlock all doors using main power window and door lock/unlock switch.
3. While pressing the back door opener switch, check voltage
between BCM connector M19 terminal 53 and ground.
Is the inspection result normal?
YES
>> GO TO 2
NO
>> GO TO 4
2.
CHECK BACK DOOR LATCH HARNESS FOR OPEN
1. Disconnect BCM and back door latch.
Terminals
Continuity
65
Ground
No
66
ALKIA0631ZZ
Connector
Terminals
Condition
Voltage (V)
(Approx.)
(+)
(-)
M19
53
Ground
Back door opener switch
is pressed
0
→
Battery voltage
for 300 ms
ALKIA1704ZZ
2010 Pathfinder
DLK-82
< COMPONENT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
DOOR LOCK ACTUATOR
2. Check continuity between BCM connector (A) M19 terminals 53
and back door latch connector (B) D502 terminal 1.
Is the inspection result normal?
YES
>> GO TO 3
NO
>> Repair or replace harness.
3.
CHECK BACK DOOR LATCH GROUND
Check continuity between back door latch connector D502 terminal
2 and ground.
Is the inspection result normal?
YES
>> Replace back door latch.
NO
>> Repair or replace harness.
4.
CHECK BACK DOOR LATCH HARNESS FOR SHORT
1. Disconnect BCM and back door latch.
2. Check continuity between BCM connector M19 terminal 53 and
ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-59, "Removal and Installation"
NO
>> Repair or replace harness.
Terminals
Continuity
53
1
Yes
ALKIA1705ZZ
Terminals
Continuity
2
Ground
Yes
ALKIA1712ZZ
Terminals
Continuity
53
Ground
No
ALKIA1706ZZ
2010 Pathfinder
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст