Nissan Pathfinder (2010 year). Instruction — part 148
GLASS HATCH LOCK ACTUATOR
DLK-83
< COMPONENT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
GLASS HATCH LOCK ACTUATOR
Description
INFOID:0000000005259925
Locks/unlocks the glass hatch with the signal from BCM.
Component Function Check
INFOID:0000000005259926
1.
CHECK FUNCTION
1. Use CONSULT-III to perform Active Test DOOR LOCK.
2. Touch “ALL LOCK” and operate glass hatch lever to ensure it is locked.
3. Touch “ALL UNLOCK” and operate glass hatch lever to ensure it is unlocked.
Is the inspection result normal?
YES
>> Glass hatch lock actuator is OK.
NO
>> Ensure glass hatch mechanical linkage is OK. Refer to
.
Diagnosis Procedure
INFOID:0000000005259927
Regarding Wiring Diagram information, refer to
DLK-131, "Wiring Diagram — POWER DOOR LOCK SYS-
1.
CHECK GLASS HATCH LOCK ACTUATOR SIGNAL
1. Turn ignition switch OFF.
2. Check voltage between BCM connector M20 terminals 65, 66
and ground.
Is the inspection result normal?
YES
>> GO TO 2
NO
>> GO TO 3
2.
CHECK GLASS HATCH LOCK ACTUATOR HARNESS
1. Disconnect BCM and glass hatch lock actuator.
2. Check continuity between BCM connector (A) M20 terminals 65,
66 and glass hatch lock actuator connector (B) D508 terminals
2, 4.
Is the inspection result normal?
YES
>> Replace glass hatch lock actuator.
Connector
Terminals
Condition
Voltage (V)
(Approx.)
(+)
(-)
M20
65
Ground
Door lock/unlock switch
is turned to LOCK
0
→
Battery voltage
for 300 ms
66
Door lock/unlock switch
is turned to UNLOCK
LIIA1048E
Terminals
Continuity
65
4
Yes
66
2
ALKIA0634ZZ
2010 Pathfinder
DLK-84
< COMPONENT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
GLASS HATCH LOCK ACTUATOR
NO
>> Repair or replace harness.
3.
CHECK GLASS HATCH LOCK ACTUATOR HARNESS
1. Disconnect BCM and glass hatch lock actuator.
2. Check continuity between BCM connector M20 terminals 65, 66
and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-59, "Removal and Installation"
NO
>> Repair or replace harness.
Terminals
Continuity
65
Ground
No
66
ALKIA0631ZZ
2010 Pathfinder
PASSENGER SELECT UNLOCK RELAY
DLK-85
< COMPONENT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
PASSENGER SELECT UNLOCK RELAY
Description
INFOID:0000000005259928
Controls the operation of both rear door lock actuators, back door latch and glass hatch lock actuators.
Component Function Check
INFOID:0000000005259929
1.
CHECK FUNCTION
1. Ensure "SELECTIVE UNLOCK FUNCTION" in WORK SUPPORT is enabled.
2. Use CONSULT-III to perform Active Test "DOOR LOCK".
3. Touch “ALL LOCK” or “ALL UNLOCK” to check that both rear doors, back door latch and glass hatch lock
actuators work normally.
Is the inspection result normal?
YES
>> Passenger select unlock relay is OK.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000005259930
Regarding Wiring Diagram information, refer to
DLK-131, "Wiring Diagram — POWER DOOR LOCK SYS-
1.
CHECK PASSENGER SELECT UNLOCK RELAY CIRCUIT
NOTE:
The passenger select unlock relay must remain connected during this step.
1. Turn ignition switch OFF.
2. Disconnect BCM and inoperative back or rear door lock actuator.
3. Check continuity between BCM connector (A) M20 terminal 65
and rear door lock actuator LH connector (B) D205 terminal 2 or
rear door lock actuator RH connector (B) D305 Terminal 2 or
glass hatch lock actuator (C) D508 terminal 4.
4. Check continuity between BCM connector M20 terminals 66 and
body ground.
Is the inspection result normal?
YES
>> GO TO 4
NO
>> GO TO 2
2.
CHECK PASSENGER SELECT UNLOCK RELAY INPUT
1. Disconnect passenger select unlock relay.
2. Check continuity between BCM connector (A) M20 terminal 65
and passenger select unlock relay connector (B) M11 terminal 3.
3. Check continuity between BCM connector (A) M20 terminal 65
and body ground.
Is the inspection result normal?
YES
>> GO TO 3
65 - 2
: Continuity should exist.
65 - 4
: Continuity should exist.
65 - Ground
: Continuity should not exist.
ALKIA1193ZZ
65 - 3
: Continuity should exist.
65 - Ground
: Continuity should not exist.
ALKIA1194ZZ
2010 Pathfinder
DLK-86
< COMPONENT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
PASSENGER SELECT UNLOCK RELAY
NO
>> Repair or replace harness between BCM and relay.
3.
CHECK PASSENGER SELECT UNLOCK RELAY OUTPUT
1. Disconnect inoperative rear door or glass hatch lock actuator.
2. Check continuity between passenger select unlock relay con-
nector (A) M11 terminal 4 and rear door lock actuator LH con-
nector (B) D205 terminal 2 or rear door lock actuator RH
connector (B) D305 terminal 2 or glass hatch lock actuator con-
nector (C) D508 terminal 4.
3. Check continuity between passenger select unlock relay con-
nector (A) M11 terminal 4 and ground.
Is the inspection result normal?
YES
>> Replace passenger select unlock relay.
NO
>> Repair or replace harness between relay and actuator.
4.
CHECK REAR DOOR LOCK ACTUATOR ASSEMBLY
1. Reconnect BCM.
2. Check voltage between rear door lock actuator connector LH (A)
D205 terminals 1 and 2 or rear door lock actuator connector RH
(A) D305 terminals 1 and 2 or glass hatch lock actuator (B)
D508 terminals 2 and 4.
3. Check voltage between rear door lock actuator connector LH (A)
D205 terminals 1 and 2 or rear door lock actuator connector RH
(A) D305 terminals 1 and 2 or glass hatch lock actuator (B)
D508 terminals 2 and 4.
Is the inspection result normal?
YES
>> Replace rear or glass hatch lock actuator.
NO
>> Repair or replace harness between actuator and splice.
4 - 2
: Continuity should exist.
4 - 4
: Continuity should exist.
4 - Ground
: Continuity should not exist.
ALKIA1195ZZ
Connector
Terminals
Condition
Voltage (V)
(Approx.)
(+)
(-)
A: D205 (LH)
A: D305 (RH)
2
1
Main power window and
door lock/unlock switch is
turned to LOCK
0
→
Battery voltage
for 300 msec.
B: D508
4
2
ALKIA1196ZZ
Connector
Terminals
Condition
Voltage (V)
(Approx.)
(+)
(-)
A: D205 (LH)
A: D305 (RH)
1
2
Main power window and
door lock/unlock switch is
turned to UNLOCK
0
→
Battery voltage
for 300 msec.
B: D508
2
4
ALKIA1197ZZ
2010 Pathfinder
INTELLIGENT KEY WARNING BUZZER
DLK-87
< COMPONENT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
INTELLIGENT KEY WARNING BUZZER
Description
INFOID:0000000005259931
Answers back and warns for an inappropriate operation.
Component Function Check
INFOID:0000000005259932
1.
CHECK FUNCTION
With CONSULT-III
Check Intelligent Key warning buzzer "OUTSIDE BUZZER" in Active Test mode.
Is the inspection result normal?
YES
>> Intelligent Key warning buzzer (engine room) is OK.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000005259933
Regarding Wiring Diagram information, refer to
DLK-149, "Wiring Diagram — INTELLIGENT KEY SYSTEM —
1.
CHECK INTELLIGENT KEY WARNING BUZZER (ENGINE ROOM) POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect Intelligent Key warning buzzer (engine room) connector.
3. Check voltage between Intelligent Key warning buzzer (engine room) harness connector E60 terminal 1
and ground.
Is the inspection normal?
YES
>> GO TO 2
NO
>> Repair or replace Intelligent Key warning buzzer (engine
room) power supply circuit.
2.
CHECK INTELLIGENT KEY WARNING BUZZER (ENGINE ROOM) CIRCUIT
1. Disconnect Intelligent Key unit connector.
2. Check continuity between Intelligent Key unit harness connector
(A) M164 terminal 4 and Intelligent Key warning buzzer (engine
room) harness connector E60 terminal 3.
3. Check continuity between Intelligent Key warning buzzer
(engine room) harness connector E60 terminal 3 and ground.
Is the inspection normal?
YES
>> GO TO 3
NO
>> Repair or replace harness between Intelligent Key warning buzzer (engine room) and Intelligent
Key unit.
3.
CHECK INTELLIGENT KEY WARNING BUZZER (ENGINE ROOM) OPERATION
DLK-88, "Component Inspection"
.
1 - Ground
: Battery voltage
WIIA1195E
4 - 3
: Continuity should exist.
3 - Ground
: Continuity should not exist.
WIIA1196E
2010 Pathfinder
DLK-88
< COMPONENT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
INTELLIGENT KEY WARNING BUZZER
>> Inspection end.
Component Inspection
INFOID:0000000005259934
1.
CHECK INTELLIGENT KEY WARNING BUZZER
Connect battery power supply to Intelligent Key warning buzzer ter-
minals 1 and 3, and check the operation.
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Replace Intelligent Key warning buzzer.
1 (BAT+) - 3 (BAT-)
: the buzzer sounds
WIIA1197E
2010 Pathfinder
INTELLIGENT KEY WARNING CHIME (COMBINATION METER)
DLK-89
< COMPONENT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
INTELLIGENT KEY WARNING CHIME (COMBINATION METER)
Description
INFOID:0000000005259935
Answers back and warns for an inappropriate operation.
Diagnosis Procedure
INFOID:0000000005259936
1.
CHECK INTELLIGENT KEY WARNING CHIME (COMBINATION METER) OPERATION
With CONSULT-III
Check Intelligent Key warning buzzer "INSIDE BUZZER" in Active Test mode.
Is the inspection result normal?
YES
>> Intelligent Key warning chime (combination meter) is OK.
NO
>> Refer to
.
2010 Pathfinder
DLK-90
< COMPONENT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
WARNING LAMP
WARNING LAMP
KEY (GREEN)
KEY (GREEN) : Description
INFOID:0000000005259937
Illuminates when the ignition knob is pushed with the presence of the Intelligent Key indicating normal opera-
tion.
KEY (GREEN) : "KEY" Warning Lamp (GREEN) Check
INFOID:0000000005259938
1.
CHECK WARNING LAMP OPERATION
With CONSULT-III
• Check “INDICATOR” in “ACTIVE TEST” mode with CONSULT-III.
• Select “BLUE ON”.
“KEY” warning lamp (green) should illuminate.
Without CONSULT-III
1. Turn ignition switch OFF.
2. Ensure Intelligent Key is in your possession inside the vehicle.
3. While monitoring the combination meter warning lamps, push the ignition knob switch.
4. The "KEY" warning lamp (green) should illuminate indicating that the Intelligent Key is nearby.
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Check combination meter. Refer to
.
KEY (RED)
KEY (RED) : Description
INFOID:0000000005259939
Illuminates when the ignition knob is pushed without the presence of the Intelligent Key indicating inappropri-
ate operation.
KEY (RED) : "KEY" Warning Lamp (RED) Check
INFOID:0000000005259940
1.
CHECK WARNING LAMP OPERATION
With CONSULT-III
• Check “INDICATOR” in “ACTIVE TEST” mode with CONSULT-III.
• Select “RED ON”.
“KEY” warning lamp (red) should illuminate.
Without CONSULT-III
1. Turn ignition switch OFF.
2. Ensure Intelligent Key is outside and away from the vehicle.
3. While monitoring the combination meter warning lamps, push the ignition knob switch.
4. The "KEY" warning lamp (red) should illuminate indicating that the Intelligent Key is not nearby.
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Check combination meter. Refer to
.
WARNING LAMP
WARNING LAMP : Description P-SHIFT
INFOID:0000000005259941
Illuminates when the ignition knob is turned from ON to OFF with the shift lever out-of-park indicating inappro-
priate operation.
2010 Pathfinder
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст