Nissan Pathfinder (2010 year). Instruction — part 414
LICENSE LAMP FINISHER
EXT-21
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
LICENSE LAMP FINISHER
Removal and Installation
INFOID:0000000005259118
REMOVAL
1. Remove the back door finisher. Refer to
INT-24, "Removal and Installation"
2. Remove the vapor barrier plastic.
3. Remove the license lamp nuts and remove the license lamp finisher.
INSTALLATION
Installation is in the reverse order of removal.
1.
Back door
2.
License lamp finisher
A.
License lamp finisher nuts
AWKIA0065ZZ
2010 Pathfinder
EXT-22
< ON-VEHICLE REPAIR >
FENDER PROTECTOR
FENDER PROTECTOR
Component
INFOID:0000000005259119
Front Fender Protector
Rear Fender Protector
WIIA1078E
1.
Front fender protector LH shown
2.
Nut
3.
Clip C205
4.
Grommet
Vehicle front
LIIA1764E
1.
Rear fender protector RH
2.
Clips
3.
Nuts
4.
Rear fender protector LH
2010 Pathfinder
FENDER PROTECTOR
EXT-23
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
Removal and Installation of Front Fender Protector
INFOID:0000000005259120
REMOVAL
1. Remove the front mud flap (if equipped). Refer to
EXT-24, "Removal and Installation"
.
2. Remove the screws.
3. Remove the plastic clips.
4. Remove the pushpins.
5. Remove the front fender protector.
INSTALLATION
Installation is in the reverse order of removal.
Removal and Installation of Rear Fender Protector
INFOID:0000000005259121
REMOVAL
1. Remove the rear mud flap (if equipped). Refer to
EXT-24, "Removal and Installation"
2. Remove the screws.
3. Remove the plastic clips.
4. Remove the pushpins.
5. Remove the rear fender protector.
INSTALLATION
Installation is in the reverse order of removal.
2010 Pathfinder
EXT-24
< ON-VEHICLE REPAIR >
RUNNING BOARDS
RUNNING BOARDS
Removal and Installation
INFOID:0000000005259122
REMOVAL
1. Remove the mud flaps (if equipped).
2. Remove the bolts and remove the running board from the running board brackets.
3. Remove the nuts and remove the running board brackets from the chassis.
4. Remove the screw and clip and remove the wind deflector.
INSTALLATION
Installation is in the reverse order of removal.
1.
Front mud flap (if equipped)
2.
Running board
3.
Rear wheel wind deflector
4.
Rear mud flap (if equipped)
5.
Running board bracket
LIIA1779E
2010 Pathfinder
ROOF RACK
EXT-25
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
ROOF RACK
Removal and Installation
INFOID:0000000005259123
REMOVAL
1. Pry outward releasing the clips and remove the slide rail cover front LH and RH.
2. Pry outward releasing the clips and remove the slide rail cover rear LH and RH.
3. Remove the bolts and remove front and rear fixed crossbars, if equipped from slide rails.
4. Remove the bolts from the slide rails LH and RH.
5. Shift the slide rails forward to disengage from the center stanchion and remove.
6. Remove the bolts and remove the center stansions LH and RH.
INSTALLATION
Installation is in the reverse order of removal.
1.
Slide rail
2.
Fixed crossbar (if equipped)
3.
Slide rail cover rear
4.
Center stanchion
5.
Slide rail cover front
A.
Clip C101
Vehicle front
AWKIA0087GB
2010 Pathfinder
EXT-26
< ON-VEHICLE REPAIR >
DOOR OUTSIDE MOLDING
DOOR OUTSIDE MOLDING
Removal and Installation
INFOID:0000000005259124
DOOR OUTSIDE MOLDING
Removal
1. Lift molding from the front side off of flange.
2. Remove the door outside molding.
Installation
Installation is in the reverse order of removal.
LIIA1780E
2010 Pathfinder
SIDE GUARD MOLDING
EXT-27
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
SIDE GUARD MOLDING
Removal and Installation
INFOID:0000000005259125
Removal
CAUTION:
Never apply tack-paper adhesive remover to body panel surface finished with lacquer-based paints.
• Original side guard molding is affixed to body panel with double-faced adhesive tape.
1. Heat molding to between 30
°
and 40
°
C (86
°
to 104
°
F) with a heat gun.
2. Raise end of molding to release clips, then cut away tape to remove molding. Remove all traces of tape.
Installation
• On vehicles coated with Hard Clear Coat, use double-faced 3M adhesive tape Product No. 4210 or equiva-
lent, after priming with 3M primer Product No. N200 or C-100 or equivalent.
• The repair parts are also affixed with double-faced adhesive tape.
• To re-use existing molding, clean all traces of double-faced adhesive tape from the molding and apply new
double-faced adhesive tape to the molding.
1. Clean the panel surface with isopropyl alcohol or equivalent to degrease the surface.
2. Heat the panel and molding tape surface to 30
°
to 40
°
C (86
°
to 104
°
F).
3. Apply the side guard molding.
• Remove the backing sheet from the tape surface.
• Align the locating pin into the hole in the outer door.
• Continue aligning the pins into their corresponding holes in the outer door during installation.
4. Press ends by hand and use a roller to apply 5 kg-f (11 lbs-f) to press molding to door surface.
• Apply even pressure along molding to insure proper wet out.
CAUTION:
To secure contact, do not wash vehicle for 24 hours after installation.
1.
Alignment hole
2.
Double-faced adhesive tape
3.
Front door side guard molding
4.
Rear door side guard molding
LIIA2724E
2010 Pathfinder
FAX-1
TRANSMISSION & DRIVELINE
C
E
F
G
H
I
J
K
L
M
SECTION
FAX
A
B
FAX
N
O
P
CONTENTS
FRONT AXLE
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Precaution . . . . . . . . . . . . . . . .....
Precaution Necessary for Steering Wheel Rota-
tion After Battery Disconnect . . . . . . . . .....
PREPARATION . . . . . . . . . . .
PREPARATION . . . . . . . . . . . . ...
Special Service Tool . . . . . . . . . . . .....
Commercial Service Tool . . . . . . . . . . ..
SYMPTOM DIAGNOSIS . . . . . . . ...
NOISE, VIBRATION, AND HARSHNESS
(NVH) TROUBLESHOOTING . . . . . . . .
NVH Troubleshooting Chart . . . . . . . . . ..
ON-VEHICLE MAINTENANCE . . . . . .
WHEEL HUB . . . . . . . . . . . . . ...
On-Vehicle Inspection and Service . . . . . . ...
REMOVAL AND INSTALLATION . . . .
DRIVE SHAFT . . . . . . . . . . . . . .
VQ40DE . . . . . . . . . . . . . . . . . ...
VQ40DE : Removal and Installation . . . . . . ..
VK56DE . . . . . . . . . . . . . . . . . ...
VK56DE : Removal and Installation . . . . . . .
WHEEL HUB . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
DISASSEMBLY AND ASSEMBLY . . . ..
DRIVE SHAFT . . . . . . . . . . . . ...
VQ40DE . . . . . . . . . . . . . . . . . .
VQ40DE : Disassembly and Assembly . . . . ...
VK56DE . . . . . . . . . . . . . . . . . ..
VK56DE : Disassembly and Assembly . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . . .
VQ40DE . . . . . . . . . . . . . . . . . .
VQ40DE : Wheel Bearing . . . . . . . . . .
VQ40DE : Drive Shaft . . . . . . . . . . . ..
VQ40DE : Boot Bands . . . . . . . . . . . .
VK56DE . . . . . . . . . . . . . . . . . ..
VK56DE : Wheel Bearing . . . . . . . . . .
VK56DE : Drive Shaft . . . . . . . . . . . ..
VK56DE : Boot Bands . . . . . . . . . . . .
2010 Pathfinder
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст