Nissan Pathfinder (2010 year). Instruction — part 439
HA-46
< ON-VEHICLE REPAIR >
HIGH-PRESSURE PIPE
HIGH-PRESSURE PIPE
Removal and Installation for Front High-pressure A/C Pipe
INFOID:0000000005256846
REMOVAL
1. Remove the front right wheel and tire assembly. Refer to
.
2. Remove the front right mud guard.
3. Remove the front right splash shield.
4. Discharge the refrigerant. Refer to
HA-37, "HFC-134a (R-134a) Service Procedure"
.
5. Remove the front low pressure A/C pipe. Refer to
HA-50, "Removal and Installation for Front Low-Pres-
.
6. Remove the front high-pressure A/C pipe. Refer to
CAUTION:
Cap or wrap the joint of the pipe with suitable material such as vinyl tape to avoid the entry of air.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Replace the O-ring of the front high-pressure A/C pipe with a new one, then apply compressor oil to
it for installation.
• After charging refrigerant, check for leaks.
Removal and Installation for Rear High- and Low-Pressure A/C Pipes
INFOID:0000000005256847
REMOVAL
1. Discharge the refrigerant. Refer to
HA-37, "HFC-134a (R-134a) Service Procedure"
.
2. Remove the luggage side lower finisher RH. Refer to
.
3. Remove the rear high- and low-pressure A/C pipes. Refer to
CAUTION:
Cap or wrap the joint of the pipe with suitable material such as vinyl tape to avoid the entry of air.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Replace the O-ring of the rear high- and low-pressure A/C pipes with a new one, then apply compres-
sor oil to it for installation.
• After charging refrigerant, check for leaks.
Removal and Installation for Underfloor Rear High- and Low-Pressure A/C and Heater
Core Pipes
INFOID:0000000005256848
REMOVAL
1. Release the fuel pressure. Refer to
(VK56DE).
2. Drain the engine coolant. Refer to
CO-12, "Changing Engine Coolant"
3. Disconnect the negative battery terminal.
4. Discharge the refrigerant. Refer to
HA-37, "HFC-134a (R-134a) Service Procedure"
.
5. Remove the front and rear RH wheels and tires. Refer to
.
6. Remove the rear bumper. Refer to
EXT-16, "Removal and Installation"
7. Disconnect the fuel filler pipe and vent pipe from the lower fuel filler hose and fuel tank.
8. Remove the front fender protector. Refer to
EXT-23, "Removal and Installation of Front Fender Protector"
.
9. Disconnect the chassis harness connector.
10. Disconnect the fuel feed hose quick connectors. Disconnect the quick connectors as follows:
2010 Pathfinder
HIGH-PRESSURE PIPE
HA-47
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
J
K
L
M
A
B
HA
N
O
P
• Hold the sides of the connector, push in the tabs and pull out the tube.
• If the connector and the tube are stuck together, push and pull several times until they start to move.
Then disconnect them by pulling.
CAUTION:
• The quick connector can be disconnected when the tabs
are completely depressed. Do not twist the quick connec-
tor more than necessary.
• Do not use any tools to disconnect the quick connector.
• Keep the resin tube away from heat. Be especially careful
when welding near the tube.
• Prevent any acid liquids such as battery electrolyte, from
getting on the resin tube.
• Do not bend or twist the resin tube during connection.
• Do not remove the remaining retainer on the hard tube (or
the equivalent) except when the resin tube or the retainer
is replaced.
• When the resin tube or hard tube, or the equivalent, is
replaced, also replace the retainer with a new one (semi-
transparent colored retainer).
• To keep the quick connector clean and to avoid damage
and contamination from foreign materials, cover the quick
connector with plastic bags or suitable material as shown.
11. Disconnect the frame mounted brake tubes from the brake system. Refer to
lation of Front Brake Piping and Brake Hose"
12. Remove the upper radiator mounting plates. Refer to
13. Disconnect the A/C lines ground strap.
14. Disconnect the exhaust system ground strap. Refer to
EX-7, "Removal and Installation"
.
15. Disconnect each end of the underfloor rear high- and low-pressure A/C and heater core pipes. Refer to
.
CAUTION:
Cap or wrap the joint of the pipes with suitable material such as vinyl tape to avoid the entry of air.
16. Remove the front floor heat shield.
17. Remove the heater pipe heat shield.
18. Disconnect the steering column from the power steering gear. Refer to
ST-19, "Removal and Installation"
.
19. Set four suitable jacks at the body mount points to support the vehicle body when it is separated from the
frame.
20. Remove the body mount bolts. Refer to
.
PBIC1268E
PBIC0163E
2010 Pathfinder
HA-48
< ON-VEHICLE REPAIR >
HIGH-PRESSURE PIPE
21. Use the vehicle hoist to lower the frame from the body [approximately 457 mm (18 in)] until there is suffi-
cient clearance for the underfloor rear high- and low-pressure A/C and heater core pipes from the body.
22. Remove the underfloor rear high- and low-pressure A/C and heater core pipes.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Replace the O-ring of the underfloor rear high- and low-pressure A/C and heater core pipes with a
new one, then apply compressor oil to it for installation.
• After charging refrigerant, check for leaks.
• Bleed the brake system. Refer to
BR-20, "Bleeding Brake System"
.
2010 Pathfinder
LOW-PRESSURE FLEXIBLE HOSE
HA-49
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
J
K
L
M
A
B
HA
N
O
P
LOW-PRESSURE FLEXIBLE HOSE
Removal and Installation for Front Low-Pressure Flexible A/C Hose
INFOID:0000000005256849
REMOVAL
1. Remove the front right wheel and tire assembly. Refer to
.
2. Remove the front right mud guard.
3. Remove the front right splash shield.
4. Discharge the refrigerant. Refer to
HA-37, "HFC-134a (R-134a) Service Procedure"
.
CAUTION:
Cap or wrap the joint of the pipe with suitable material such as vinyl tape to avoid the entry of air.
5. Remove the front low-pressure flexible A/C hose. Refer to
.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Replace the O-ring of the front low-pressure flexible A/C hose with a new one, then apply compres-
sor oil to it for installation.
• After charging refrigerant, check for leaks.
2010 Pathfinder
HA-50
< ON-VEHICLE REPAIR >
LOW-PRESSURE PIPE
LOW-PRESSURE PIPE
Removal and Installation for Front Low-Pressure A/C Pipe
INFOID:0000000005256850
REMOVAL
1. Discharge the refrigerant. Refer to
HA-37, "HFC-134a (R-134a) Service Procedure"
.
2. Disconnect the heater pump connector.
3. Remove the heater pump from the bracket and reposition out of the way. Do not disconnect the heater
hoses from the heater pump.
4. Remove the front low-pressure A/C pipe. Refer to
CAUTION:
Cap or wrap the joint of the pipe with suitable material such as vinyl tape to avoid the entry of air.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Replace the O-ring of the front low-pressure A/C pipe with a new one, then apply compressor oil to it
for installation.
• After charging refrigerant, check for leaks.
Removal and Installation for Rear High- and Low-Pressure A/C Pipes
INFOID:0000000005256851
REMOVAL
1. Discharge the refrigerant. Refer to
HA-37, "HFC-134a (R-134a) Service Procedure"
.
2. Remove the luggage side lower finisher RH. Refer to
.
3. Remove the rear high- and low-pressure A/C pipes. Refer to
CAUTION:
Cap or wrap the joint of the pipe with suitable material such as vinyl tape to avoid the entry of air.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Replace the O-ring of the rear high- and low-pressure A/C pipes with a new one, then apply compres-
sor oil to it for installation.
• After charging refrigerant, check for leaks.
Removal and Installation for Underfloor Rear High- and Low-Pressure A/C and Heater
Core Pipes
INFOID:0000000005256852
REMOVAL
1. Release the fuel pressure. Refer to
(VK56DE).
2. Drain the engine coolant. Refer to
CO-12, "Changing Engine Coolant"
3. Disconnect the negative battery terminal.
4. Discharge the refrigerant. Refer to
HA-37, "HFC-134a (R-134a) Service Procedure"
.
5. Remove the front and rear RH wheels and tires. Refer to
.
6. Remove the rear bumper. Refer to
EXT-16, "Removal and Installation"
7. Disconnect the fuel filler pipe and vent pipe from the lower fuel filler hose and fuel tank.
8. Remove the front fender protector. Refer to
EXT-23, "Removal and Installation of Front Fender Protector"
.
9. Disconnect the chassis harness connector.
10. Disconnect the fuel feed hose quick connectors. Disconnect the quick connectors as follows:
• Hold the sides of the connector, push in the tabs and pull out the tube.
2010 Pathfinder
LOW-PRESSURE PIPE
HA-51
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
J
K
L
M
A
B
HA
N
O
P
• If the connector and the tube are stuck together, push and pull several times until they start to move.
Then disconnect them by pulling.
CAUTION:
• The quick connector can be disconnected when the tabs
are completely depressed. Do not twist the quick connec-
tor more than necessary.
• Do not use any tools to disconnect the quick connector.
• Keep the resin tube away from heat. Be especially careful
when welding near the tube.
• Prevent any acid liquids such as battery electrolyte, from
getting on the resin tube.
• Do not bend or twist the resin tube during connection.
• Do not remove the remaining retainer on the hard tube (or
the equivalent) except when the resin tube or the retainer
is replaced.
• When the resin tube or hard tube, or the equivalent, is
replaced, also replace the retainer with a new one (semi-
transparent colored retainer).
• To keep the quick connector clean and to avoid damage
and contamination from foreign materials, cover the quick
connector with plastic bags or suitable material as shown.
11. Disconnect the frame mounted brake tubes from the brake system. Refer to
lation of Front Brake Piping and Brake Hose"
12. Remove the upper radiator mounting plates. Refer to
13. Disconnect the A/C lines ground strap.
14. Disconnect the exhaust system ground strap. Refer to
EX-7, "Removal and Installation"
.
15. Disconnect each end of the underfloor rear high- and low-pressure A/C and heater core pipes. Refer to
.
CAUTION:
Cap or wrap the joint of the pipes with suitable material such as vinyl tape to avoid the entry of air.
16. Remove the front floor heat shield.
17. Remove the heater pipe heat shield.
18. Disconnect the steering column from the power steering gear. Refer to
ST-19, "Removal and Installation"
.
19. Set four suitable jacks at the body mount points to support the vehicle body when it is separated from the
frame.
20. Remove the body mount bolts. Refer to
.
21. Use the vehicle hoist to lower the frame from the body [approximately 457 mm (18 in)] until there is suffi-
cient clearance for the underfloor rear high- and low-pressure A/C and heater core pipes from the body.
PBIC1268E
PBIC0163E
2010 Pathfinder
HA-52
< ON-VEHICLE REPAIR >
LOW-PRESSURE PIPE
22. Remove the underfloor rear high- and low-pressure A/C and heater core pipes.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Replace the O-ring of the underfloor rear high- and low-pressure A/C and heater core pipes with a
new one, then apply compressor oil to it for installation.
• After charging refrigerant, check for leaks.
• Bleed the brake system. Refer to
BR-20, "Bleeding Brake System"
.
2010 Pathfinder
CONDENSER
HA-53
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
J
K
L
M
A
B
HA
N
O
P
CONDENSER
Removal and Installation for Condenser
INFOID:0000000005256853
REMOVAL
1. Discharge the refrigerant. Refer to
HA-37, "HFC-134a (R-134a) Service Procedure"
.
2. Remove the radiator. Refer to
CO-44, "Removal and Installation"
(VQ40DE).
CAUTION:
Be careful not to damage the core surface of the condenser and the radiator.
3. Disconnect the front high-pressure flexible A/C hose and the front high-pressure A/C pipe from the con-
denser.
CAUTION:
Cap or wrap the joint of the pipes with suitable material such as vinyl tape to avoid the entry of air.
4. Disconnect the refrigerant pressure sensor harness connector.
5. Remove the refrigerant pressure sensor from the condenser.
6. Lift the condenser out of the mounting grommets and remove
the condenser.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Replace the O-rings of the front high-pressure A/C pipe, refrigerant pressure sensor, and front high-
pressure flexible A/C hose with new ones, then apply compressor oil to them for installation.
• After charging refrigerant, check for leaks.
• Replace the mounting grommets as necessary.
LJIA0177E
2010 Pathfinder
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст