Nissan Tiida C11. Instruction — part 731
EM-276
< ON-VEHICLE REPAIR >
[K9K]
TURBOCHARGER
Inspection
INFOID:0000000001381481
INSPECTION AFTER REMOVAL
CAUTION:
When the compressor wheel turbine wheel or rotor shaft is damaged, remove all the fragments and
foreign matter left in the following passages in order to prevent a secondary failure:
MBIB1419E
Suction side
: Between turbocharger and air cleaner
Exhaust side
: Between turbocharger and catalyst
EXHAUST MANIFOLD
EM-277
< ON-VEHICLE REPAIR >
[K9K]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
EXHAUST MANIFOLD
Exploded View
INFOID:0000000001381482
Removal and Installation
INFOID:0000000001381483
REMOVAL
1.
Remove battery ground cable.
2.
Remove turbocharger assembly. Refer to
EM-275, "Removal and Installation"
3.
Remove air duct (inlet). Refer to
.
4.
Remove blow-by tube.
5.
Remove air duct (suction). Refer to
.
6.
Remove EGR tube. Refer to
.
7.
Loosen exhaust manifold nuts in the reverse order as shown.
Then remove exhaust manifold.
CAUTION:
Be careful not to deform turbocharger piping when removing
the assembly.
INSTALLATION
1.
Catalyst
2.
Bracket
3.
Turbocharger
4.
Exhaust manifold
5.
EGR unit
6.
Gasket
A.
To transaxle
B.
To exhaust front tube
⇐
Engine front
AWBIA0120GB
MBIB1417E
EM-278
< ON-VEHICLE REPAIR >
[K9K]
EXHAUST MANIFOLD
1.
Clean the surface of exhaust manifold and cylinder head.
2.
Install new gasket to cylinder head.
3.
Tighten the exhaust manifold nuts in numerical order as shown.
4.
Installation is in the reverse order of removal for the remaining
components.
Inspection
INFOID:0000000001381484
INSPECTION AFTER INSTALLATION
Start engine and raise engine speed to check for exhaust emission leaks.
: 26.0 N·m (2.7 kg-m, 19 ft-lb)
MBIB1417E
GLOW PLUG
EM-279
< ON-VEHICLE REPAIR >
[K9K]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
GLOW PLUG
Exploded View
INFOID:0000000001381485
Removal and Installation
INFOID:0000000001381486
REMOVAL
CAUTION:
Remove glow plug only if necessary. If carbon adheres, it may be stuck and broken.
1.
Disconnect battery ground cable.
2.
Remove air duct (inlet). Refer to
.
3.
Remove engine cover. Refer to
EM-270, "Removal and Installation"
.
4.
Remove charge air cooler tubes and hoses at EGR unit and electronic throttle control actuator. Refer to
.
5.
Remove high pressure pipes protection cover. Refer to
.
6.
Disconnect harness connector from glow plug.
7.
Remove glow plug.
CAUTION:
• When removing or installing, do not use such tools as an air impact wrench.
• Handle it carefully without giving any impact, even after removal. [As a guide, if it drops from
height of 10 cm (3.94 in) or higher, always replace it.]
INSTALLATION
1.
Remove adhered carbon from glow plug installation hole with a suitable tool.
2.
Install glow plug.
3.
Installation is in the reverse order of removal.
1.
Glow plug
: Engine front
E1BIA0005GB
: 15.0 N·m (1.5 kg-m, 11 ft-lb)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст