Nissan Tiida C11. Instruction — part 730
EM-272
< ON-VEHICLE REPAIR >
[K9K]
EGR SYSTEM
EGR SYSTEM
Exploded View
INFOID:0000000001381474
Removal and Installation
INFOID:0000000001381475
REMOVAL
1.
Remove battery ground cable.
2.
Remove engine undercover using power tool.
3.
Drain engine coolant. Refer to
4.
Remove lower radiator hose. Refer to
5.
Remove cowl top cover and cowl top extension assembly. Refer to
EXT-20, "Removal and Installation"
6.
Remove air cleaner and air duct assembly. Refer to
EM-269, "Removal and Installation"
7.
Remove charge air cooler inlet tubes at EGR assembly. Refer to
.
8.
Disconnect EGR volume control valve and electronic throttle control actuator connectors.
9.
Disconnect heater hoses from EGR cooler cover.
10. Remove EGR cooler cover.
11. Remove front engine slinger.
12. Remove air inlet tube.
13. Remove RH fender protector. Refer to
EXT-22, "Removal and Installation"
1.
Air inlet tube
2.
Engine slinger
3.
O-ring
4.
Bracket
5.
EGR tube
6.
Gasket
7.
EGR cooler
8.
Gasket
9.
EGR volume control valve
10. Gasket
11.
EGR volume control valve housing
12. Clamp
13. EGR tube
14. Gasket
15. Gasket
16. Electronic throttle control actuator
17. O-ring
18. EGR cooler cover
A.
To intake manifold
B.
To exhaust manifold
E1BIA0025GB
EGR SYSTEM
EM-273
< ON-VEHICLE REPAIR >
[K9K]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
14. Remove front driveshaft assembly RH. Refer to
FAX-11, "Removal and Installation (Right Side)"
.
15. Remove electronic throttle control actuator.
16. Remove driveshaft center bearing bracket. Refer to
FAX-11, "Removal and Installation (Right Side)"
.
17. Remove front exhaust tube. Refer to
.
18. Remove catalytic converter. Refer to
19. Remove EGR tube.
20. Remove EGR assembly.
INSTALLATION
Installation is in the reverse order of removal.
EM-274
< ON-VEHICLE REPAIR >
[K9K]
CATALYST
CATALYST
Exploded View
INFOID:0000000001381476
Removal and Installation
INFOID:0000000001381477
REMOVAL
1.
Remove battery ground cable.
2.
Remove engine undercover using power tool.
3.
Remove cowl top cover and cowl top extension assembly. Refer to
EXT-20, "Removal and Installation"
4.
Remove engine cover.
5.
Remove front driveshaft assembly. Refer to
FAX-11, "Removal and Installation (Right Side)"
6.
Remove driveshaft center bearing bracket. Refer to
FAX-11, "Removal and Installation (Right Side)"
.
7.
Remove exhaust front tube. Refer to
.
8.
Remove catalyst bolts and brackets.
9.
Remove catalyst.
INSTALLATION
Installation is in the reverse order of removal.
Inspection
INFOID:0000000001381478
INSPECTION AFTER INSTALLATION
Start engine and raise engine speed to check for exhaust emission leaks.
1.
Catalyst
2.
Bracket
3.
Turbocharger
4.
Exhaust manifold
5.
EGR unit
6.
Gasket
A.
To transaxle
B.
To exhaust front tube
⇐
Engine front
AWBIA0120GB
TURBOCHARGER
EM-275
< ON-VEHICLE REPAIR >
[K9K]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
TURBOCHARGER
Exploded View
INFOID:0000000001381479
Removal and Installation
INFOID:0000000001381480
REMOVAL
1.
Remove catalyst. Refer to
EM-274, "Removal and Installation"
.
2.
Remove turbocharger oil supply tube.
NOTE:
After applying penetrative lubricant to the mounting nuts, check for the penetration of the lubricant, and
then loosen the nuts to remove.
3.
Remove turbocharger oil outlet tube.
NOTE:
After applying penetrative lubricant to the mounting nuts, check for the penetration of the lubricant, and
then loosen the nuts to remove.
4.
Remove air duct (suction). Refer to
.
5.
Disconnect turbocharger vacuum hose.
6.
Remove turbocharger from exhaust manifold.
CAUTION:
Do not disassemble or adjust the turbocharger body.
INSTALLATION
Installation is in the reverse order of removal.
NOTE:
Apply engine oil to lubricate the turbocharger oil tubes.
1.
Washer
2.
Turbocharger oil supply tube
3.
O-ring
4.
Turbocharger
5.
Exhaust manifold
6.
Gasket
7.
Turbocharger oil outlet tube
8.
Gasket
MBIB1418E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст