Nissan Tiida C11. Instruction — part 734
EM-288
< ON-VEHICLE REPAIR >
[K9K]
HIGH PRESSURE SUPPLY PUMP
15. Plug all the holes of the injection circuit.
16. Remove the three mounting bolts from the high pressure supply pump then remove it.
INSTALLATION
1.
Install the pump then position the mounting bolts without tightening them.
2.
Before fitting the new injection tube, lightly lubricate the nut threads with the oil from the sachet provided
in the new parts kit.
3.
Install the injection tubes according to the following:
• remove the protective plugs.
• insert the injection tube olive into the taper of the high pressure pump outlet.
• insert the injection tube olive into the taper of the high pressure rail inlet.
4.
Finger tighten the nuts of the injection tube starting with the one located on the rail side.
5.
Tighten the bolts on the high pressure pump.
6.
Tighten the injection tube nut.
7.
Install the high pressure supply pump protector.
CAUTION:
When installing the high pressure supply pump protector, follow the steps below.
• Be sure rubber spacer (1) is touching bolt head of high
pressure supply pump (4) as shown.
• Tighten bolt (2) while holding protector towards the high
pressure supply pump.
• Tighten nut (3).
• Be sure rubber spacer (1) is touching bolt head of high
pressure supply pump (4).
8.
Installation is in the reverse order to removal.
9.
Test the sealing of the high pressure supply pump after it has been repaired (refer to
).
: 21.0 N·m (2.1 kg-m, 15 ft-lb)
: 24.0 N·m (2.4 kg-m, 18 ft-lb)
E1BIA0117ZZ
: 21.0 N·m (2.1 kg-m, 15 ft-lb)
: 21.0 N·m (2.1 kg-m, 15 ft-lb)
E1BIA0118ZZ
ROCKER COVER
EM-289
< ON-VEHICLE REPAIR >
[K9K]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
ROCKER COVER
Exploded View
INFOID:0000000001381497
Removal and Installation
INFOID:0000000001381498
REMOVAL
1.
Remove engine cover.
2.
Remove air duct (inlet). Refer to
.
3.
Remove air duct (suction). Refer to
.
4.
Remove charge air cooler pipes and hoses. Refer to
5.
Disconnect and remove camshaft position sensor.
6.
Remove fuel hose shield.
7.
Disconnect electronic throttle control actuator. Refer to
8.
Remove blow-by hose.
9.
Remove high pressure pipes protection cover (upper).
10. Unclip fuel injector spill hose from rocker cover.
11. Unclip timing belt upper cover.
12. Remove rocker cover.
NOTE:
Loosen bolts in the reverse order as shown.
INSTALLATION
1.
Install new gasket to rocker cover.
1.
Oil filler cap
2.
Rocker cover
3.
Gasket
4.
Camshaft position sensor
E1BIA0006GB
E1BIA0048ZZ
EM-290
< ON-VEHICLE REPAIR >
[K9K]
ROCKER COVER
2.
Apply liquid gasket on locations shown.
Use Genuine Liquid gasket or equivalent.
3.
Tighten bolts in the numerical order as shown.
4.
Installation is in the reverse order of removal.
MBIB0581E
: 12.0 N·m (1.2 kg-m, 9 ft-lb)
E1BIA0048ZZ
TIMING BELT
EM-291
< ON-VEHICLE REPAIR >
[K9K]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
TIMING BELT
Exploded View
INFOID:0000000001381499
Removal and Installation
INFOID:0000000001381500
CAUTION:
• Apply new engine oil to parts marked in illustration before installation.
• Replace any belt that has been removed.
• Never turn the engine in the direction opposite to that of normal operation.
• When replacing the timing belt, be sure to replace the timing belt tensioner.
• Do not run the engine without the drive belts to avoid damaging the crankshaft pulley.
REMOVAL
1.
Remove front wheel RH. Refer to
.
2.
Remove fender protector RH. Refer to
EXT-22, "Removal and Installation"
3.
Remove engine cover.
4.
Remove drive belt. Refer to
EM-291, "Removal and Installation"
5.
Support the engine using suitable tool.
6.
Remove RH engine torque rod.
7.
Remove RH engine mounting support bracket and RH engine mounting insulator.
1.
Timing belt inner cover
2.
Timing belt
3.
Camshaft sprocket
4.
Camshaft sprocket stud bolt
5.
Timing belt tensioner
6.
Timing belt cover
7.
Cylinder head suspended bracket
8.
Crankshaft pulley
9.
Crankshaft sprocket (timing belt)
10. Oil seal
11.
Crankshaft cover
12. Gasket
A.
30.0 N·m (3.1 kg-m, 22 ft-lb) and 86 degrees
B.
120.0 N·m (12 kg-m, 89 ft-lb) and 95 degrees
E1BIA0022GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст