Nissan Tiida C11. Instruction — part 733
EM-284
< ON-VEHICLE REPAIR >
[K9K]
OIL PAN
OIL PAN
Exploded View
INFOID:0000000001381492
Removal and Installation
INFOID:0000000001381493
CAUTION:
To avoid the danger of being scalded, never drain the engine oil when the engine is hot.
REMOVAL
1.
Remove engine undercover using power tool.
2.
Remove oil level indicator.
3.
Drain engine oil. Refer to
.
CAUTION:
Perform when engine is cold.
4.
Remove fender protector (RH).
5.
Remove front driveshaft assembly (RH). Refer to
FAX-11, "Removal and Installation (Right Side)"
6.
Remove driveshaft center bearing bracket.
7.
Remove rear torque rod (lower). Refer to
.
8.
Remove bolts from the catalyst bracket. Refer to
.
9.
Disconnect and remove oil level sensor.
1.
Gasket
2.
Oil pan
3.
O-ring
4.
Drain plug
5.
Oil level sensor
6.
Clutch housing
7.
Crankshaft position sensor
E1BIA0008GB
OIL PAN
EM-285
< ON-VEHICLE REPAIR >
[K9K]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
10. Remove oil pan and transaxle joint bolts.
11. Support the engine bottom of the oil pan with a transmission jack
etc.
12. Remove oil pan bolts in reverse order as shown.
13. Insert seal cutter [SST: KV10111100 (—)] between upper oil pan
and cylinder block. Slide tool by tapping on the side of the tool
with a hammer.
CAUTION:
Exercise care not to damage mating surface.
14. Remove oil pan.
INSTALLATION
• Installation is in the reverse order of removal.
MBIB1039E
MBIB0575E
MBIB1257E
SEM365EA
EM-286
< ON-VEHICLE REPAIR >
[K9K]
OIL PAN
1.
Apply liquid gasket as shown.
• Use Genuine Liquid Gasket or equivalent.
2.
Using suitable tool, align the oil pan with the cylinder block.
3.
Install oil pan bolts in numerical order as shown.
NOTE:
Wait at least 30 minutes after oil pan is installed before filling
engine with engine oil.
Inspection
INFOID:0000000001381494
INSPECTION AFTER REMOVAL
Clean oil pump assembly if any objects attached.
INSPECTION AFTER INSTALLATION
• Check the engine oil level. Refer to
.
• Start the engine and make sure there are no leaks of engine oil. Refer to
.
MBIB0593E
MBIB0594E
: 14.0 N·m (1.4 kg-m, 10 ft-lb)
MBIB1257E
HIGH PRESSURE SUPPLY PUMP
EM-287
< ON-VEHICLE REPAIR >
[K9K]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
HIGH PRESSURE SUPPLY PUMP
Exploded View
INFOID:0000000001381495
Removal and Installation
INFOID:0000000001381496
REMOVAL
CAUTION:
• Be sure to read “Precautions for Diesel Equipment”. Refer to
EM-253, "Precaution for Diesel Equip-
• Wait until the fuel temperature drops before carrying out any work.
• Order the special high pressure injection circuit plug kit.
• It is strictly forbidden to remove any high pressure supply
pump sprocket marked number 070 575 (see diagram). If the
pump is being replaced, the pulley must be replaced.
1.
Disconnect the battery.
2.
Remove air duct (inlet). Refer to
.
3.
Remove engine cover.
4.
Remove blow-by hose.
5.
Remove charge air cooler hose and pipes. Refer to
6.
Remove the RH front tire. Refer to
.
7.
Remove fender protector (RH). Refer to
.
8.
Remove drive belt. Refer to
EM-263, "Removal and Installation"
9.
Support the engine using suitable tool.
10. Remove the timing belt. Refer to
EM-291, "Removal and Installation"
11. Remove the oil level gauge guide and plug the hole. Refer to
.
12. Remove high pressure pipes protection cover (upper). Refer to
.
13. Carefully disconnect:
• The connectors from the flow actuator,
• The connectors from the fuel temperature sensor,
• On the pump, the fuel supply and return pipes.
• The return pipe connecting the injectors with the pump.
14. Remove the injection tube connecting the pump to the rail. Refer to
EM-281, "Removal and Installation"
.
1.
High pressure supply pump protec-
tor
2.
Stud bolt
3.
High pressure supply pump
4.
Engine cover bracket
E1BIA0119GB
MBIB9036E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст