Nissan Tiida C11. Instruction — part 1100
MWI-90
< SYMPTOM DIAGNOSIS >
THE OIL PRESSURE WARNING LAMP DOES NOT TURN OFF
THE OIL PRESSURE WARNING LAMP DOES NOT TURN OFF
Description
INFOID:0000000001538679
The oil pressure warning lamp remains illuminated while the engine is running (normal oil pressure).
Diagnosis Procedure
INFOID:0000000001538680
1.
CHECK OIL PRESSURE WARNING LAMP
Perform auto active test. Refer to
PCS-10, "Diagnosis Description"
Is oil pressure warning lamp illuminated?
YES
>> GO TO 2
NO
>> Replace combination meter. Refer to
MWI-94, "Removal and Installation"
2.
CHECK IPDM E/R OUTPUT VOLTAGE
1.
Turn ignition switch OFF.
2.
Disconnect the oil pressure switch connector.
3.
Turn ignition switch ON.
4.
Check voltage between the oil pressure switch harness connec-
tor F32 terminal 1 and ground.
Is the inspection result normal?
YES
>> GO TO 3
NO
>> GO TO 4
3.
CHECK OIL PRESSURE SWITCH
Perform a unit check for the oil pressure switch. Refer to
MWI-31, "Component Inspection"
Is the inspection result normal?
YES
>> Replace IPDM E/R. Refer to
PCS-30, "Removal and Installation of IPDM E/R"
.
NO
>> Replace oil pressure switch.
4.
CHECK OIL PRESSURE SWITCH SIGNAL CIRCUIT
check the oil pressure switch signal circuit. Refer to
.
Is the inspection result normal?
YES
>> Replace IPDM E/R. Refer to
PCS-30, "Removal and Installation of IPDM E/R"
.
NO
>> Repair harness or connector.
1 – Ground
: Approx. 12V
PKIC1144E
MWI
THE AMBIENT TEMPERATURE DISPLAY IS INCORRECT
MWI-91
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
THE AMBIENT TEMPERATURE DISPLAY IS INCORRECT
Description
INFOID:0000000001538673
• The displayed ambient air temperature is higher than the actual temperature.
• The displayed ambient air temperature is lower than the actual temperature.
Diagnosis Procedure
INFOID:0000000001538674
NOTE:
Check that the symptom is not applicable to the normal operating condition before starting diagnosis. Refer to
MWI-17, "INFORMATION DISPLAY : System Description"
1.
CHECK AMBIENT SENSOR SIGNAL CIRCUIT
Check the ambient sensor signal circuit. Refer to
Is the inspection result normal?
YES
>> GO TO 2
NO
>> Repair harness or connector.
2.
CHECK AMBIENT SENSOR UNIT
Perform a unit check for the ambient sensor. Refer to
HAC-131, "Ambient Sensor Component Inspection"
(without NAVI) or
HAC-245, "Ambient Sensor Component Inspection"
(with NAVI).
Is the inspection result normal?
YES
>> Replace combination meter. Refer to
MWI-94, "Removal and Installation"
NO
>> Replace ambient sensor.
MWI-92
< SYMPTOM DIAGNOSIS >
NORMAL OPERATING CONDITION
NORMAL OPERATING CONDITION
INFORMATION DISPLAY
INFORMATION DISPLAY : Description
INFOID:0000000001538681
OUTSIDE AIR TEMPERATURE
The displayed outside air temperature on the information display may differ from the actual temperature
because it is a corrected value calculated from the ambient sensor signal by the combination meter. Refer to
MWI-17, "INFORMATION DISPLAY : System Description"
for details on the correction process.
MWI
PRECAUTIONS
MWI-93
< PRECAUTION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
PRECAUTION
PRECAUTIONS
Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSION-
ER"
INFOID:0000000001374731
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SR and SB section of
this Service Instruction.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Instruction. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст