Nissan Tiida C11. Instruction — part 1099
MWI-86
< ECU DIAGNOSIS >
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
DTC Index
INFOID:0000000001713130
NOTE:
The details of TIME display are as follows.
• CRNT: The malfunctions that are detected now
• 1 - 39: The number is indicated when it is normal at present and a malfunction was detected in the past. It
increases like 0
→
1
→
2 ··· 38
→
39 after returning to the normal condition whenever IGN OFF
→
ON. It is
fixed to 39 until the self-diagnosis results are erased if it is over 39. It returns to 0 when a malfunction is
detected again in the process.
CONSULT-III display
Fail-safe
TIME
NOTE
Refer to
No DTC is detected.
further testing
may be required.
—
—
—
—
U1000: CAN COMM CIRCUIT
×
CRNT
1 – 39
MWI
THE FUEL GAUGE POINTER DOES NOT MOVE
MWI-87
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
SYMPTOM DIAGNOSIS
THE FUEL GAUGE POINTER DOES NOT MOVE
Description
INFOID:0000000001374712
Fuel gauge needle will not move from a certain position.
Diagnosis Procedure
INFOID:0000000001374713
1.
CHECK COMBINATION METER INPUT SIGNAL
1.
Select “METER/M&A” on CONSULT-III.
2.
Using “FUEL METER” of “DATA MONITOR”, compare the monitor value with the fuel gauge reading on
the combination meter. Refer to
MWI-29, "Component Function Check"
Does monitor value match fuel gauge reading?
YES
>> GO TO 2
NO
>> Replace combination meter. Refer to
MWI-94, "Removal and Installation"
2.
CHECK FUEL LEVEL SENSOR SIGNAL CIRCUIT
Check the fuel level sensor signal circuit. Refer to
.
Is the inspection result normal?
YES
>> GO TO 3
NO
>> Repair harness or connector.
3.
CHECK FUEL LEVEL SENSOR UNIT
Perform a unit check for the fuel level sensor unit. Refer to
MWI-30, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 4
NO
>> Replace fuel level sensor unit and fuel pump. Refer to
FL-8, "Removal and Installation"
4.
CHECK FLOAT INTERFERENCE
Check that the float arm does not interfere or bind with any of the components in the fuel tank.
Is the inspection result normal?
YES
>> Replace combination meter. Refer to
MWI-94, "Removal and Installation"
NO
>> Repair or replace malfunctioning parts.
MWI-88
< SYMPTOM DIAGNOSIS >
THE FUEL GAUGE POINTER DOES NOT MOVE TO "F" WHEN REFUELING
THE FUEL GAUGE POINTER DOES NOT MOVE TO "F" WHEN REFUEL-
ING
Description
INFOID:0000000001374714
The fuel gauge needle will not move to “F” position when refueling.
Diagnosis Procedure
INFOID:0000000001374715
1.
OBSERVE FUEL GAUGE
Does it take a long time for the pointer to move to FULL position?
YES or NO
YES
>> GO TO 2
NO
>> GO TO 3
2.
IDENTIFY FUELING CONDITION
Was the vehicle fueled with the ignition switch ON?
YES or NO
YES
>> Be sure to fuel the vehicle with the ignition switch OFF. Otherwise, it will take a long time to move
to FULL position because of the characteristic of the fuel gauge.
NO
>> GO TO 3
3.
OBSERVE VEHICLE POSITION
Is the vehicle parked on an incline?
YES or NO
YES
>> Check the fuel level indication with vehicle on a level surface.
NO
>> GO TO 4
4.
OBSERVE FUEL GAUGE POINTER
During driving, does the fuel gauge pointer move gradually toward EMPTY position?
YES or NO
YES
>> Check the components. Refer to
MWI-30, "Component Inspection"
NO
>> The float arm may interfere or bind with any of the components in the fuel tank.
MWI
THE OIL PRESSURE WARNING LAMP DOES NOT TURN ON
MWI-89
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
THE OIL PRESSURE WARNING LAMP DOES NOT TURN ON
Description
INFOID:0000000001538677
The oil pressure warning lamp stays off when the ignition switch is turned ON.
Diagnosis Procedure
INFOID:0000000001538678
1.
CHECK OIL PRESSURE WARNING LAMP
Perform auto active test. Refer to
PCS-10, "Diagnosis Description"
Is oil pressure warning lamp illuminated?
YES
>> GO TO 2
NO
>> Replace combination meter. Refer to
MWI-94, "Removal and Installation"
2.
CHECK OIL PRESSURE SWITCH SIGNAL CIRCUIT
Check the oil pressure switch signal circuit. Refer to
Is the inspection result normal?
YES
>> GO TO 3
NO
>> Repair harness or connector.
3.
CHECK OIL PRESSURE SWITCH UNIT
Perform a unit check for the oil pressure switch. Refer to
MWI-31, "Component Inspection"
.
Is the inspection result normal?
YES
>> Replace IPDM E/R. Refer to
PCS-30, "Removal and Installation of IPDM E/R"
.
NO
>> Replace oil pressure switch.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст