Nissan Tiida C11. Instruction — part 1378
REPAIR FOR COMPONENT PARTS
TM-563
< DISASSEMBLY AND ASSEMBLY >
[TYPE 2 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
• Measure thickness (t) of dish plate. Replace if damaged, deformed
or worn.
Forward Clutch and Overrun Clutch Spring Retainer Assembly
Check length (L) of spring retainer assembly. Replace if damaged,
deformed or worn.
CAUTION:
Do not remove return springs (A) from spring retainer (B)
Forward Clutch Drum
• Make sure that check balls do not stick.
• Apply compressed air to check ball oil hole from outside of forward
clutch drum. Make sure air leaks past ball.
• Apply compressed air to oil hole from inside of forward clutch
drum. Make sure there is no air leakage.
Overrun Clutch Piston
• Make sure that check balls do not stick.
• Apply compressed air to check ball oil hole opposite return spring.
Make sure there is no air leakage.
• Apply compressed air to oil hole on return spring side. Make sure
that air leaks through ball hole.
ASSEMBLY
Thickness of dish plate (t)
Forward clutch:
2.5 mm (0.098 in)
Overrun clutch:
2.15 mm (0.0846 in)
SAT163D
Length (L):
27.7 mm (0.1091 in)
SCIA7025J
SAT213D
SAT212D
TM-564
< DISASSEMBLY AND ASSEMBLY >
[TYPE 2 (4AT: RE4F03B)]
REPAIR FOR COMPONENT PARTS
1.
Install seal rings (1) and D-rings (2) on forward clutch piston (3)
and overrun clutch piston (4).
CAUTION:
Be careful with the direction of seal rings (1).
2.
Install overrun clutch piston on forward clutch piston by turning it
slowly.
CAUTION:
Apply ATF to inner surface of forward clutch piston.
3.
Install forward clutch piston with overrun clutch piston on for-
ward clutch drum by turning it slowly.
CAUTION:
Apply ATF to inner surface of forward clutch drum.
4.
Align notch in forward clutch piston with groove in forward clutch
drum.
5.
Install spring retainer assembly (1) on overrun clutch piston (2).
SCIA6005J
SAT215D
SAT216D
SAT217D
SCIA6019J
REPAIR FOR COMPONENT PARTS
TM-565
< DISASSEMBLY AND ASSEMBLY >
[TYPE 2 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
6.
Set Tool on spring retainer assembly, and install snap ring while
compressing spring retainer assembly.
CAUTION:
• Set Tool directly over return springs.
• Do not expand snap ring excessively.
• Do not align snap ring gap with spring retainer assembly
stopper.
7.
Install dish plate (5), driven plates (4), drive plates (3) and retain-
ing plate (2) for overrun clutch.
(1): Snap ring
(2): Retaining plate
(3): Drive plate
(4): Driven plate
(5): Dish plate
Drive plate/Driven plate: 3/4
CAUTION:
Be careful with the order of plates.
8.
Install snap ring for overrun clutch using suitable tool.
9.
Measure clearance between overrun clutch retaining plate and
snap ring using feeler gauge. If not within allowable limit, select
proper retaining plate.
SAT205D
SAT134F
SCIA5993E
SCIA4895E
Specified clearance
Standard and allowable limit:
.
SAT227D
TM-566
< DISASSEMBLY AND ASSEMBLY >
[TYPE 2 (4AT: RE4F03B)]
REPAIR FOR COMPONENT PARTS
10. Install dish plate (5), driven plates (4), drive plates (3) and retain-
ing plate (2) for forward clutch.
(1): Snap ring
(2): Retaining plate
(3): Drive plate
(4): Driven plate
(5): Dish plate
Drive plate/Driven plate: 5/5
CAUTION:
Be careful with the order of plates.
11. Install snap ring for forward clutch using suitable tool.
12. Measure clearance between forward clutch retaining plate and
snap ring using feeler gauge. If not within allowable limit, select
proper retaining plate.
13. Check operation of forward clutch and overrun clutch. Refer to
TM-267, "Forward and Overrun Clutches"
Low & Reverse Brake
INFOID:0000000001731443
COMPONENTS
SCIA5992E
SCIA4894E
Specified clearance
Standard and allowable limit:
.
SAT228D
SCIA6007J
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст