Nissan Tiida C11. Instruction — part 1260
DTC P0755 SHIFT SOLENOID VALVE B
TM-91
< COMPONENT DIAGNOSIS >
[TYPE 1 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
3.
Check continuity between terminal cord assembly harness con-
nector terminal and TCM connector terminal.
4.
If OK, check harness for short to ground and short to power.
5.
If OK, check continuity between ground and transaxle assembly.
6.
Reinstall any part removed.
OK or NG
OK
>> GO TO 4.
NG
>> Repair open circuit or short to ground or short to power in harness or connectors.
4.
CHECK VALVE RESISTANCE
1.
Turn ignition switch OFF.
2.
Disconnect terminal cord assembly connector in engine room.
3.
Check resistance between terminal cord assembly harness con-
nector terminal and ground.
OK or NG
OK
>> GO TO 5.
NG
>> Repair or replace damaged parts.
5.
CHECK DTC
Perform
TM-89, "DTC Confirmation Procedure"
.
OK or NG
OK
>> INSPECTION END
NG
>> GO TO 6.
6.
CHECK TCM
1.
Check TCM input/output signal. Refer to
.
2.
If NG, recheck TCM pin terminals for damage or loose connection with harness connector.
OK or NG
OK
>> INSPECTION END
NG
>> Repair or replace damaged parts.
Component Inspection
INFOID:0000000001694371
SHIFT SOLENOID VALVE B
• For removal, refer to
TM-191, "Control Valve Assembly and Accumulators"
.
Resistance Check
Item
Connector
Terminal
Continuity
TCM
E101
12
Yes
Terminal cord assembly
harness connector
F30
1
SCIA3255E
Solenoid valve
Connector
Terminal
Resistance (Approx.)
Shift solenoid valve B
F30
1 - Ground
5 - 20
Ω
SCIA3454E
TM-92
< COMPONENT DIAGNOSIS >
[TYPE 1 (4AT: RE4F03B)]
DTC P0755 SHIFT SOLENOID VALVE B
• Check resistance between terminal and ground.
Operation Check
• Check solenoid valve by listening for its operating sound while
applying battery voltage to the terminal and ground.
Solenoid valve
Terminal
Resistance (Ap-
prox.)
Shift solenoid valve B
1
Ground
5 - 20
Ω
SCIA2055E
SCIA2058E
DTC P1760 OVERRUN CLUTCH SOLENOID VALVE
TM-93
< COMPONENT DIAGNOSIS >
[TYPE 1 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
DTC P1760 OVERRUN CLUTCH SOLENOID VALVE
Description
INFOID:0000000001694378
The overrun clutch solenoid valve is activated by the TCM in response to signals sent from the PNP switch,
overdrive control switch, vehicle speed and ECM (throttle opening). The overrun clutch operation will then be
controlled.
CONSULT-III Reference Value in Data Monitor Mode
INFOID:0000000001694379
Remarks: Specification data are reference values.
On Board Diagnosis Logic
INFOID:0000000001694380
• This is an OBD self-diagnostic item.
• Diagnostic trouble code “P1760 OVERRUN CLUTCH S/V” with CONSULT-III or 6th judgement flicker with-
out CONSULT-III is detected when TCM detects an improper voltage drop when it tries to operate solenoid
valve.
Possible Cause
INFOID:0000000001694381
• Harness or connector
(The solenoid circuit is open or shorted.)
• Overrun clutch solenoid valve
DTC Confirmation Procedure
INFOID:0000000001694382
CAUTION:
• Always drive vehicle at a safe speed.
• If performing this “DTC Confirmation Procedure” again, always turn ignition switch OFF and wait at
least 10 seconds before continuing.
After the repair, perform the following procedure to confirm the malfunction is eliminated.
WITH CONSULT-III
1.
Turn ignition switch ON and select “DATA MONITOR” mode for “A/T” with CONSULT-III.
2.
Touch “START”.
3.
Start engine.
4.
Accelerate vehicle to a speed of more than 10 km/h (6 MPH) with “D” position (OD ON).
5.
Release accelerator pedal completely with “D” position (OD OFF).
6.
If the check result is NG, go to
WITH GST
Follow the procedure “WITH CONSULT-III”.
WITHOUT CONSULT-III
1.
Start engine.
2.
Drive vehicle under the following conditions:
Selector lever position: “D” position (OD ON)
Vehicle speed: Higher than 10 km/h (6 MPH)
3.
Perform self-diagnosis. Refer to
TM-38, "Diagnosis Procedure without CONSULT-III"
4.
If the check result is NG, go to
Diagnosis Procedure
INFOID:0000000001694384
1.
CHECK INPUT SIGNAL
With CONSULT-III
Item name
Condition
Display value
OVERRUN/C S/V
When overrun clutch solenoid valve operates. (When
overrun clutch disengaged. Refer to
.)
ON
When overrun clutch solenoid valve does not operate.
(When overrun clutch engaged. Refer to
.)
OFF
TM-94
< COMPONENT DIAGNOSIS >
[TYPE 1 (4AT: RE4F03B)]
DTC P1760 OVERRUN CLUTCH SOLENOID VALVE
1.
Start engine.I
2.
Select “MAIN SIGNALS” in “DATA MONITOR” mode for “A/T” with CONSULT-II.
3.
Read out the value of “OVERRUN/C S/V” while driving.
Check the value changes according to driving speed.
Without CONSULT-III
1.
Start engine.
2.
Check voltage between TCM connector terminal and ground.
OK or NG
OK
>> GO TO 5.
NG
>> GO TO 2.
2.
CHECK OVERRUN CLUTCH SOLENOID VALVE CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect TCM connector.
3.
Check resistance between TCM connector terminal and ground.
OK or NG
OK
>> GO TO 5.
NG
>> GO TO 3.
3.
CHECK HARNESS BETWEEN TCM AND TERMINAL CORD ASSEMBLY HARNESS CONNECTOR
1.
Turn ignition switch OFF.
2.
Disconnect terminal cord assembly harness connector and TCM connector.
Item name
Condition
Display value
OVERRUN/C S/V
When overrun clutch solenoid valve oper-
ates. (When overrun clutch disengaged.
Refer to
.)
ON
When overrun clutch solenoid valve does
not operate. (When overrun clutch en-
gaged. Refer to
OFF
Item
Connec-
tor
Terminal
Condition
Judge-
ment stan-
dard
(Approx.)
Overrun
clutch sole-
noid valve
E31
20 -
Ground
When overrun clutch so-
lenoid valve operates.
(When overrun clutch dis-
engaged. Refer to
Battery
voltage
When overrun clutch so-
lenoid valve dose not op-
erate. (When overrun
clutch engaged. Refer to
.)
0V
SCIA3258E
Solenoid Valve
Connector
Terminal
Resistance (Ap-
prox.)
Overrun clutch solenoid
valve
E31
20 - Ground
20 - 30
Ω
SCIA3259E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст