Nissan Tiida C11. Instruction — part 1261
DTC P1760 OVERRUN CLUTCH SOLENOID VALVE
TM-95
< COMPONENT DIAGNOSIS >
[TYPE 1 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
3.
Check continuity between terminal cord assembly harness con-
nector terminal and TCM connector terminal.
4.
If OK, check harness for short to ground and short to power.
5.
If OK, check continuity between ground and transaxle assembly.
6.
Reinstall any part removed.
OK or NG
OK
>> GO TO 4.
NG
>> Repair open circuit or short to ground or short to power in harness or connectors.
4.
CHECK VALVE RESISTANCE
1.
Turn ignition switch OFF.
2.
Disconnect terminal cord assembly connector in engine room.
3.
Check resistance between terminal cord assembly harness con-
nector terminal and ground.
OK or NG
OK
>> GO TO 5.
NG
>> Repair or replace damaged parts.
5.
CHECK DTC
Perform
TM-93, "DTC Confirmation Procedure"
.
OK or NG
OK
>> INSPECTION END
NG
>> GO TO 6.
6.
CHECK TCM
1.
Check TCM input/output signal. Refer to
.
2.
If NG, recheck TCM pin terminals for damage or loose connection with harness connector.
OK or NG
OK
>> INSPECTION END
NG
>> Repair or replace damaged parts.
Component Inspection
INFOID:0000000001694385
OVERRUN CLUTCH SOLENOID VALVE
• For removal, refer to
TM-191, "Control Valve Assembly and Accumulators"
.
Resistance Check
Item
Connector
Terminal
Continuity
TCM
E101
20
Yes
Terminal cord assembly
harness connector
F30
3
SCIA3260E
Solenoid valve
Connector
Terminal
Resistance (Approx.)
Overrun clutch solenoid
valve
F30
3 - Ground
20 - 30
Ω
SCIA3455E
TM-96
< COMPONENT DIAGNOSIS >
[TYPE 1 (4AT: RE4F03B)]
DTC P1760 OVERRUN CLUTCH SOLENOID VALVE
• Check resistance between terminal and ground.
Operation Check
• Check solenoid valve by listening for its operating sound while
applying battery voltage to the terminal and ground.
Solenoid valve
Terminal
Resistance (Ap-
prox.)
Overrun clutch so-
lenoid valve
3
Ground
20 - 30
Ω
SCIA2059E
SCIA2062E
DTC VEHICLE SPEED SENSOR MTR
TM-97
< COMPONENT DIAGNOSIS >
[TYPE 1 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
DTC VEHICLE SPEED SENSOR MTR
Description
INFOID:0000000001694386
The vehicle speed sensor·MTR is built into the speedometer assembly. The sensor functions as an auxiliary
device to the revolution sensor when it is malfunctioning. The TCM will then use a signal sent from the vehicle
speed sensor·MTR.
CONSULT-III Reference Value in Data Monitor Mode
INFOID:0000000001694387
Remarks: Specification data are reference values.
On Board Diagnosis Logic
INFOID:0000000001694388
• This is not an OBD self-diagnostic item.
• Diagnostic trouble code “VHCL SPEED SEN-MTR” with CONSULT-III or 2nd judgement flicker without
CONSULT-III is detected when TCM does not receive the proper voltage signal from the sensor.
Possible Cause
INFOID:0000000001694389
• Harness or connector
(The sensor circuit is open or shorted.)
• Vehicle speed sensor
DTC Confirmation Procedure
INFOID:0000000001694390
CAUTION:
• Always drive vehicle at a safe speed.
• If performing this “DTC Confirmation Procedure” again, always turn ignition switch OFF and wait at
least 10 seconds before continuing.
After the repair, perform the following procedure to confirm the malfunction is eliminated.
WITH CONSULT-III
1.
Turn ignition switch ON and select “DATA MONITOR” mode for “A/T” with CONSULT-III.
2.
Touch “START”.
3.
Start engine and accelerate vehicle from 0 to 25 km/h (0 to 16 MPH).
4.
If the check result is NG, go to
WITHOUT CONSULT-III
1.
Start engine.
2.
Drive vehicle under the following conditions:
Selector lever position: “D” position
Vehicle speed: Higher than 25 km/h (16 MPH)
3.
Perform self-diagnosis. Refer to
TM-38, "Diagnosis Procedure without CONSULT-III"
4.
If the check result is NG, go to
Diagnosis Procedure
INFOID:0000000001694392
1.
CHECK INPUT SIGNAL
With CONSULT-III
1.
Start engine.
2.
Select “TCM INPUT SIGNALS” in “DATA MONITOR” mode for “A/T” with CONSULT-III.
3.
Read out the value of “VHCL/S SE-MTR” while driving. Check the value changes according to driving
speed.
Item name
Condition
Display value
VHCL/S SE-MTR
During driving
Approximately matches the speedometer reading.
Item name
Condition
Display value
VHCL/S SE-MTR
During driving
Approximately matches
the speedometer reading.
TM-98
< COMPONENT DIAGNOSIS >
[TYPE 1 (4AT: RE4F03B)]
DTC VEHICLE SPEED SENSOR MTR
Without CONSULT-III
1.
Start engine.
2.
Check voltage between TCM connector terminal and ground.
OK or NG
OK
>> GO TO 3.
NG
>> GO TO 2.
2.
DETECT MALFUNCTIONING ITEM
Check the following items:
• Combination meter.
• Harness for short or open between TCM and combination meter.
OK or NG
OK
>> GO TO 3.
NG
>> Repair or replace damaged parts.
3.
CHECK DTC
Perform
TM-97, "DTC Confirmation Procedure"
.
OK or NG
OK
>> INSPECTION END
NG
>> GO TO 4.
4.
CHECK TCM
1.
Check TCM input/output signal. Refer to
.
2.
If NG, recheck TCM pin terminals for damage or loose connection with harness connector.
OK or NG
OK
>> INSPECTION END
NG
>> Repair or replace damaged parts.
Item
Connec-
tor
Terminal
Condition
Judgement
standard (Ap-
prox.)
Vehicle
speed sen-
sor
E32
40 -
Ground
When driving vehicle at
2 to 3 km/h (1 to 2 MPH)
for 1 m (3 ft) or more.
Voltage varies
between less
than 0V and
more than
4.5V
SCIA3246E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст