Nissan Tiida C11. Instruction — part 739
EM-308
< DISASSEMBLY AND ASSEMBLY >
[K9K]
CYLINDER HEAD
9.
Compress the valve springs using the valve lifter.
Remove the keys, upper cups and springs.
NOTE:
Before removing the valves and the valve stem seals, it is
vital to measure position “H” of one of the old seals in rela-
tion to the cylinder head using valve seal drift [KV113B0180
(Mot. 1511-01) (commercial service tool) or equivalent tool].
10. Install the push rod (A) of valve seal drift [KV113B0180 (Mot.
1511-01) (commercial service tool) or equivalent tool] on the
valve stem seal.
NOTE:
The inner diameter of the push rod must be identical to that
of the valve. In addition, the bottom of the push rod must
come into contact with the metal upper section of the valve
stem seal.
11. Install the guide tube (B) over the push rod until the guide tube
comes into contact with the cylinder head, locking the push rod
with the knurled wheel.
12. Remove the guide tube assembly plus push rod, being careful
not to loosen the knurled wheel.
13. Remove the valves and valve guide seals using the valve seal
remover [KV113B0090 (Mot. 1335) (commercial service tool) or
equivalent tool].
ASSEMBLY
MBIB0416E
MBIB0417E
MBIB0418E
MBIB0419E
CYLINDER HEAD
EM-309
< DISASSEMBLY AND ASSEMBLY >
[K9K]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
1.
Install new valves and grind them gently into their respective
seats. Clean all the parts thoroughly, mark them for identification
purposes, then carry out the refitting operation.
Lubricate the inside of the valve guide.
• It is imperative to fit the valve stem seals using valve seal drift
[KV113B0180 (Mot. 1511-01) (commercial service tool) or
equivalent tool].
NOTE:
Do not lubricate the valve stem seals before fitting them.
2.
Place the valve in the cylinder head.
3.
Place the barrel of valve seal drift [KV113B0180 (Mot. 1511-01)
(commercial service tool) or equivalent tool] over the valve stem
(the inner diameter of the barrel must be identical to the diame-
ter of the valve stem).
4.
Keep the valve pressed against its seat.
5.
Place the valve stem seal (not lubricated) over the tool barrel.
6.
Push the valve stem seal past the tool barrel, then withdraw the
barrel.
MBIB0421E
MBIB0422E
MBIB0423E
MBIB0424E
EM-310
< DISASSEMBLY AND ASSEMBLY >
[K9K]
CYLINDER HEAD
7.
Place the guide tube plus push rod assembly on the valve stem
seal.
8.
Push the valve stem seal down by tapping the top of the sleeve
with the palm of your hand until the guide tube touches the cylin-
der head.
9.
Repeat these operations for all the valves.
10. Install the valve springs and upper cups using valve spring com-
pressor.
11. Install the keys using tweezers.
12. Install in the reverse order of removal after this step.
Cleaning
INFOID:0000000001381511
• It is very important not to scratch the gasket faces of any aluminium components.
• Use suitable tool to dissolve any part of the seal which remains stuck to the metal surface.
• Apply the dissolving product to the part to be cleaned, wait approximately 10 minutes, then remove it using a
wooden spatula.
• Wear gloves while carrying out this operation.
• Do not allow this dissolving product to drip on to the paintwork.
• Great care should be taken when performing this operation, to prevent foreign objects from entering
the pipes taking oil under pressure to the camshafts (pipes in both the cylinder head and its cover)
and the oil return pipes.
• Failure to follow these instructions could lead to the blocking of the oilways, resulting in rapid and
serious damage to the engine.
Inspection
INFOID:0000000001381512
INSPECTION AFTER REMOVAL
Cylinder Head Distortion
NOTE:
When performing this inspection, cylinder block distortion should be also checked. Refer to
.
1.
Wipe off engine oil and remove water scale (like deposit), gasket, sealant, carbon, etc. with a scraper.
CAUTION:
MBIB0425E
MBIB0416E
CYLINDER HEAD
EM-311
< DISASSEMBLY AND ASSEMBLY >
[K9K]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
Use utmost care not to allow gasket debris to enter passages for engine oil or water.
2.
At each of several locations on bottom surface of cylinder head, measure the distortion in six directions
using straightedge and feeler gauge.
• If it exceeds the limit, replace cylinder head.
Cylinder Head Height
Measure the height of cylinder head (H).
Valve protrusion
Check the valve protrusion using dial gauge stand set [KV113B0040
(Mot. 251-01) (commercial service tool) or equivalent tool] and dial
gauge stand set [KV113B0050 (Mot. 252-01) (commercial service
tool) or equivalent tool] as shown.
INSPECTION AFTER DISASSEMBLY
Valve
Measure the valves as follows.
• Stem diameter (d)
• Face angle (
α
)
• Head diameter (D)
• Valve length (L)
• Valve margin (T)
Limit
: Refer to
.
Standard
: Refer to
.
E1BIA0063ZZ
Standard
:
−
0.07 to 0.07 mm (
−
0.0028 to 0.0028 in)
MBIB0426E
Intake
: Refer to
Exhaust
: Refer to
Intake
: Refer to
Exhaust
: Refer to
Intake
: Refer to
Exhaust
: Refer to
Intake
: Refer to
Exhaust
: Refer to
E1BIA0064ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст