Nissan Tiida C11. Instruction — part 1272
SYSTEM SYMPTOM
TM-139
< SYMPTOM DIAGNOSIS >
[TYPE 1 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
.
3.
Turn ignition switch OFF.
4.
Check voltage between TCM connector terminals and ground.
OK or NG
OK
>> GO TO 4.
NG
>> GO TO 3.
3.
DETECT MALFUNCTIONING ITEM
Check the following.
• Harness for short or open between ignition switch and TCM connector terminals 10, 19
• Harness for short or open between battery and TCM connector terminal 28
• 10A fuse (No.13, located in the fuse block) and 10A fuse (No.49, located in the IPDM E/R)
• Ignition switch.
OK or NG
OK
>> GO TO 4.
NG
>> Repair or replace damaged parts.
4.
CHECK TCM GROUND CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect TCM connector.
3.
Check continuity between TCM connector terminals and ground.
OK or NG
OK
>> GO TO 5.
NG
>> Repair open circuit or short to ground or short to power
in harness or connectors.
5.
DETECT MALFUNCTIONING ITEM
Check the following.
• Harness for short or open between ignition switch and combination meter
• Combination meter.
OK or NG
OK
>> GO TO 6.
NG
>> Repair or replace damaged parts.
6.
CHECK SYMPTOM
Item
Connector
Terminal
Judgement standard (Approx.)
TCM connector
E31
10
Battery voltage
19
E32
28
SCIA2656E
Item
Connector
Terminal
Judgement standard (Approx.)
TCM connector
E31
10
0V
19
0V
E32
28
Battery voltage
SCIA2657E
Item
Connector
Terminal
Continuity
TCM connector
E32
25, 48 - Ground
Yes
SCIA2671E
TM-140
< SYMPTOM DIAGNOSIS >
[TYPE 1 (4AT: RE4F03B)]
SYSTEM SYMPTOM
Check again. Refer to
TM-180, "Check Before Engine Is Started"
.
OK or NG
OK
>> INSPECTION END
NG
>> GO TO 7.
7.
CHECK TCM
1.
Check TCM input/output. Refer to
(Type 1) or
(Type 2).
2.
If NG, recheck TCM pin terminals for damage or loose connection with harness connector.
OK or NG
OK
>> INSPECTION END
NG
>> Repair or replace damaged parts.
Engine Cannot Be Started in "P" and "N" Position
INFOID:0000000001696243
SYMPTOM:
• Engine cannot be started with selector lever in “P” or “N” position.
• Engine can be started with selector lever in “D”, “2”, “1” or “R” position.
1.
CHECK SELF-DIAGNOSIS RESULTS
Perform self-diagnosis. Refer to
TM-35, "CONSULT-III Function (TRANSMISSION)"
or
Procedure without CONSULT-III"
.
Is any malfunction detected by self-diagnostic results?
YES
>> Check the malfunctioning system. Refer to
TM-35, "CONSULT-III Function (TRANSMISSION)"
or
TM-38, "Diagnosis Procedure without CONSULT-III"
.
NO
>> GO TO 2.
2.
CHECK PNP SWITCH
Check continuity between PNP switch harness connector terminals.
OK or NG
OK
>> GO TO 4.
NG
>> GO TO 3.
3.
CHECK CONTROL CABLE ADJUSTMENT
Check PNP switch again with control cable disconnected from instruction shaft of A/T assembly. Refer to test
group 2.
OK or NG
OK
>> Adjust control cable. Refer to
TM-204, "Adjustment of A/T Position"
.
NG
>> 1.
Check PNP switch (Refer to test group 2.) again after adjusting PNP switch (Refer to
).
-
If OK, INSPECTION END
-
If NG, repair or replace PNP switch. Refer to
TM-195, "Park/Neutral Position (PNP) Switch"
4.
CHECK STARTING SYSTEM
Check starting system. Refer to
OK or NG
OK
>> INSPECTION END
NG
>> Repair or replace damaged parts.
In "P" Position, Vehicle Moves Forward or Backward When Pushed
INFOID:0000000001696244
SYMPTOM:
Vehicle moves when it is pushed forward or backward with selector lever in “P” position.
Selector lever position
Connector
terminal
Continuity
“P”, “N”
F25
1 - 2
Yes
Other positions
No
SCIA5606E
SYSTEM SYMPTOM
TM-141
< SYMPTOM DIAGNOSIS >
[TYPE 1 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
1.
CHECK A/T POSITION
Check A/T position. Refer to
TM-204, "Checking of A/T Position"
OK or NG
OK
>> GO TO 2.
NG
>> Adjust A/T position. Refer to
TM-204, "Adjustment of A/T Position"
.
2.
CHECK PARKING COMPONENTS
Check parking components. Refer to
and
.
OK or NG
OK
>> INSPECTION END
NG
>> Repair or replace damaged parts.
In "N" Position, Vehicle Moves
INFOID:0000000001696245
SYMPTOM:
Vehicle moves forward or backward when selecting “N” position.
1.
CHECK A/T POSITION
Check A/T position. Refer to
TM-204, "Checking of A/T Position"
OK or NG
OK
>> GO TO 2.
NG
>> Adjust A/T position. Refer to
TM-204, "Adjustment of A/T Position"
.
2.
CHECK A/T FLUID LEVEL
Check A/T fluid level. Refer to
OK or NG
OK
>> GO TO 3.
NG
>> Refill ATF.
3.
CHECK A/T FLUID CONDITION
1.
Remove oil pan. Refer to
2.
Check A/T fluid condition. Refer to
.
OK or NG
OK
>> GO TO 5.
NG
>> GO TO 4.
4.
DETECT MALFUNCTIONING ITEM
1.
Disassemble A/T. Refer to
2.
Check the following items:
-
Forward clutch assembly. Refer to
TM-267, "Forward and Overrun Clutches"
-
Overrun clutch assembly. Refer to
TM-267, "Forward and Overrun Clutches"
.
-
Reverse clutch assembly. Refer to
OK or NG
OK
>> GO TO 5.
NG
>> Repair or replace damaged parts.
5.
CHECK SYMPTOM
OK or NG
OK
>> INSPECTION END
SAT282F
TM-142
< SYMPTOM DIAGNOSIS >
[TYPE 1 (4AT: RE4F03B)]
SYSTEM SYMPTOM
NG
>> GO TO 6.
6.
CHECK TCM
1.
Check TCM input/output signals. Refer to
TM-22, "Input/Output Signal of TCM"
2.
If NG, recheck TCM pin terminals for damage or loose connection with harness connector.
OK or NG
OK
>> INSPECTION END
NG
>> Repair or replace damaged parts.
Large Shock "N"
→
"R" Position
INFOID:0000000001696246
SYMPTOM:
There is a large shock when changing from “N” to “R” position.
1.
CHECK SELF-DIAGNOSTIC RESULTS
Perform self-diagnosis. Refer to
TM-35, "CONSULT-III Function (TRANSMISSION)"
or
Procedure without CONSULT-III"
.
Is any malfunction detected by self-diagnostic results?
YES
>> Check the malfunctioning system. Refer to
TM-38, "Diagnosis Procedure without CONSULT-III"
.
NO
>> GO TO 2.
2.
CHECK LINE PRESSURE
Check line pressure at idle with selector lever in “D” position. Refer to
TM-178, "Inspection and Judgment"
OK or NG
OK
>> GO TO 4.
NG
>> GO TO 3.
3.
DETECT MALFUNCTIONING ITEM
1.
Remove control valve assembly. Refer to
TM-191, "Control Valve Assembly and Accumulators"
2.
Check the following items:
-
Valves to control line pressure (Pressure regulator valve, pressure modifier valve, pilot valve and pilot fil-
ter)
-
Line pressure solenoid valve
-
Oil pump assembly. Refer to
OK or NG
OK
>> GO TO 4.
NG
>> Repair or replace damaged parts.
4.
CHECK SYMPTOM
Check again. Refer to
.
OK or NG
OK
>> INSPECTION END
NG
>> GO TO 5.
5.
CHECK TCM
1.
Check TCM input/output signals. Refer to
TM-22, "Input/Output Signal of TCM"
2.
If NG, recheck TCM pin terminals for damage or loose connection with harness connector.
OK or NG
OK
>> INSPECTION END
NG
>> Repair or replace damaged parts.
Vehicle Does Not Creep Backward in "R" Position
INFOID:0000000001696247
SYMPTOM:
Vehicle does not creep backward when selecting “R” position.
1.
CHECK A/T FLUID LEVEL
Check A/T fluid level. Refer to
OK or NG
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст