Nissan Tiida C11. Instruction — part 929
INT-34
< ON-VEHICLE REPAIR >
HEADLINING
14. Disconnect antenna feeder cable near rear pillar finisher LH.
15. Disengage the dual lock fastener on the backside of headlining.
• Insert a suitable tool into the edge of dual lock fastener, then move the tool side to side horizontally to
release it.
CAUTION:
Excessive up and down force may cause roof panel damage.
16. Position the headlining so the front edge goes through the open-
ing of the right side front door.
17. Position the headlining so the rear edge goes through the open-
ing of the left rear door, then remove headlining.
CAUTION:
• 2 technicians should be used to avoid damage when remov-
ing or replacing headlining.
• During headlining removal and installation, cover the center
console finisher upper surface to prevent damage.
• Set A/T shift lever to the D position, and make a space to
remove front end of headlining right side.
• Do not bend headlining when removing.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
Avoid headlining damage when installing by inserting rear clips first during assembly.
PIIB2586J
PIIB6049E
TRUNK ROOM TRIM & TRUNK LID FINISHER
INT-35
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
TRUNK ROOM TRIM & TRUNK LID FINISHER
Removal and Installation
INFOID:0000000001329058
REMOVAL
CAUTION:
• Insert a trim stick or suitable tool between panel on vehicle
and clips (as indicated with arrow) to release clips.
• Be careful not to damage the body while prying to release
clips.
• Make sure clips are properly aligned in panel holes on body
when installing, then press them in completely.
1.
Open trunk lid.
2.
Position the rear seat cushion to the forward most position, then
remove the rear seatback and seatback side RH/LH. Refer to
SE-18, "Removal and Installation"
.
3.
Release the clips, then remove the seatback finisher RH/LH.
4.
Lift and remove the trunk floor carpet.
1.
Trunk side finisher RH
2.
Seat back finisher RH (if equipped)
3.
Trunk floor carpet
4.
Seat back finisher LH (if equipped)
5.
Trunk side finisher LH
6.
Trunk rear plate
7.
Trunk lid finisher inner
A.
Clip C205
⇐
Vehicle front
AWJIA0063ZZ
SIIA0810E
INT-36
< ON-VEHICLE REPAIR >
TRUNK ROOM TRIM & TRUNK LID FINISHER
5.
Release the clips, then remove the trunk rear plate.
6.
Release the clips, then remove the trunk side finisher RH/LH.
7.
Release the clips and remove the trunk lid finisher inner from the trunk lid.
INSTALLATION
Installation is in the reverse order of removal.
IP-1
BODY INTERIOR
C
D
E
F
G
H
I
K
L
M
SECTION
IP
A
B
IP
N
O
P
CONTENTS
INSTRUMENT PANEL
SERVICE INFORMATION . . . . . . .
PRECAUTIONS . . . . . . . . . . . . ...
Precaution . . . . . . . . . . . . . . . .....
PREPARATION . . . . . . . . . . . . ...
Commercial Service Tool . . . . . . . . . . ..
SQUEAK AND RATTLE TROUBLE DIAG-
NOSES . . . . . . . . . . . . . . . ...
Work Flow . . . . . . . . . . . . . . . . .
Generic Squeak and Rattle Troubleshooting . . ....
Diagnostic Worksheet . . . . . . . . . . . ...
INSTRUMENT PANEL ASSEMBLY . . . . .
Component Parts . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст