Nissan Tiida C11. Instruction — part 928
INT-30
< ON-VEHICLE REPAIR >
HEADLINING
LHD Sedan Models Shown, RHD Similar
7.
Roof console/map lamp assembly (if
equipped)
8.
Antenna feeder cable
9.
Room lamp
10. Dual lock fastener
11. Room lamp harness
12. Insulator
13. Finisher
A.
With sunroof
B.
Without sunroof
Metal clip
Clip C103
⇐
Vehicle front
LIIA2925E
HEADLINING
INT-31
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
Removal and Installation - Hatchback
INFOID:0000000001329056
REMOVAL
1.
Remove the negative and positive battery cables.
2.
Remove front seat assembly RH/LH. Refer to
SE-14, "Removal and Installation"
.
3.
Remove rear seat cushion and rear seatback. Refer to
SE-18, "Removal and Installation"
.
4.
Remove front seat belt shoulder anchor RH/LH. Refer to
SB-6, "Removal and Installation of Front Seat
5.
Remove center console body assembly. Refer to
IP-11, "Removal and Installation"
6.
Remove front pillar garnish RH/LH. Refer to
INT-20, "Removal and Installation"
7.
Remove antenna feeder cable clip, then disconnect antenna
feeder cable connector.
8.
Remove front and rear kicking plate inner RH/LH, center pillar lower garnish, center pillar upper garnish,
front and rear body side welt RH/LH. Refer to
INT-20, "Removal and Installation"
.
WARNING:
Do not reuse center pillar upper garnish if removed.
9.
Remove back door weatherstrip. Refer to
INT-18, "Removal and Installation"
.
10. Release the clips using a suitable tool, then remove the front
and rear assist grips.
11. Remove the sunvisor caps and screws, then remove sunvisor RH/LH.
1.
Headlining
2.
Assist grip
3.
Room lamp
4.
Sunvisor
5.
Cap
6.
Sunvisor holder
7.
Map lamp assembly (if equipped)
8.
Antenna feeder cable
9.
Roof console assembly (if
equipped)
10. Roof plate (if equipped)
11. Dual lock fastener
12. Insulator
13. Room lamp harness
14. Cover
A.
With sunroof
B.
Without sunroof
Clip C103
⇐
Vehicle front
PIIB2583J
PIIB2584J
INT-32
< ON-VEHICLE REPAIR >
HEADLINING
12. Remove sunvisor holders RH/LH by rotating 45 degrees, then
pulling outward.
13. Release the metal clips, then remove the roof console/map lamp assembly (if equipped).
14. Release remaining headlining clips.
15. Disconnect antenna feeder cable near rear pillar finisher LH.
16. Disengage the dual lock fastener on the backside of headlining.
• Insert a suitable tool into the edge of dual lock fastener, then move the tool side to side horizontally to
release it.
CAUTION:
Excessive up and down force may cause roof panel damage.
17. Position the headlining so the front edge goes through the open-
ing of the right side front door.
18. Position the headlining so the rear edge goes through the open-
ing of the left rear door, then remove headlining.
CAUTION:
• 2 technicians should be used to avoid damage when remov-
ing or replacing headlining.
• During headlining removal and installation, cover the center
console finisher upper surface to prevent damage.
• Set A/T shift lever to the D position, and make a space to
remove front end of headlining right side.
• Do not bend headlining when removing.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
PIIB3982J
PIIB2586J
PIIB6049E
PIIB6050E
HEADLINING
INT-33
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
Avoid headlining damage when installing by inserting rear clips first during assembly.
Removal and Installation - Sedan
INFOID:0000000001329057
REMOVAL
1.
Remove the negative and positive battery cables.
2.
Remove front seat assembly RH/LH. Refer to
SE-14, "Removal and Installation"
.
3.
Remove rear seat cushion and rear seatback. Refer to
SE-18, "Removal and Installation"
.
4.
Remove front seat belt shoulder anchor RH/LH. Refer to
SB-6, "Removal and Installation of Front Seat
5.
Remove center console body assembly. Refer to
IP-11, "Removal and Installation"
6.
Remove front pillar garnish RH/LH. Refer to
INT-20, "Removal and Installation"
7.
Remove antenna feeder cable clip, then disconnect antenna
feeder cable connector.
8.
Remove front and rear kicking plate inner RH/LH, center pillar lower garnish, center pillar upper garnish,
front and rear body side welt RH/LH. Refer to
INT-20, "Removal and Installation"
.
WARNING:
Do not reuse center pillar upper garnish if removed.
9.
Release the clips using a suitable tool, then remove the front
and rear assist grips.
10. Remove the sunvisor caps and screws, then remove sunvisor RH/LH.
11. Remove sunvisor holders RH/LH by rotating 45 degrees, then
pulling outward.
12. Release the metal clips, then remove the roof console/map lamp assembly (if equipped).
13. Release remaining headlining clips.
PIIB2583J
PIIB2584J
PIIB3982J
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст