Nissan Tiida C11. Instruction — part 925
INT-18
< ON-VEHICLE REPAIR >
BACK DOOR TRIM
BACK DOOR TRIM
Removal and Installation
INFOID:0000000001329114
REMOVAL
CAUTION:
• Insert a suitable tool between panel on vehicle and clips (as
indicated with arrow) to release clips.
• Use a suitable tool when removing metal clips from garnishes.
• Be careful not to damage the body while prying to release
clips.
• Make sure clips are properly aligned in panel holes on body
when installing, then press them in completely.
1.
Open back door.
2.
Release the clips, then lift upward to release the pawls and
remove the back door finisher lower.
3.
Release the clips, then remove back door side garnish RH/LH.
4.
Release the clips, then remove back door finisher upper from the back door.
INSTALLATION
Installation is in the reverse order of removal.
1.
Back door finisher upper
2.
Back door weatherstrip
3.
Back door side garnish (RH)
4.
Cover
5.
Back door finisher lower
6.
Back door side garnish (LH)
7.
Back door
Pawl
Metal clip
Clip C101
⇐
Vehicle front
LIIA2577E
SIIA0810E
BODY SIDE TRIM
INT-19
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
BODY SIDE TRIM
Component
INFOID:0000000001329051
Hatchback Models
AWJIA0060ZZ
1.
Front pillar garnish
2.
Front body side welt
3.
Front kicking plate inner
4.
Front kicking plate outer
5.
Center pillar lower garnish
6.
Rear kicking plate inner
7.
Rear pillar finisher
8.
Rear body side welt
9.
Rear kicking plate outer
10. Center pillar upper garnish
Pawl
Metal clip
Clip
⇐
Vehicle front
INT-20
< ON-VEHICLE REPAIR >
BODY SIDE TRIM
Sedan Models
Removal and Installation
INFOID:0000000001329052
WARNING:
Do not reuse center pillar upper garnish if removed.
CAUTION:
• Insert a suitable tool between panel on vehicle and clips (as
indicated with arrow) to release clips.
• Use a suitable tool when removing metal clips from garnishes.
• Be careful not to damage the body while prying to release
clips.
• Make sure clips are properly aligned in panel holes on body
when installing, then press them in completely.
• When releasing molded-in pawls or resin clips, follow the
steps below to prevent garnish or clip damage.
AWJIA0061ZZ
1.
Front pillar garnish
2.
Front body side welt
3.
Front kicking plate inner
4.
Front kicking plate outer
5.
Center pillar lower garnish
6.
Rear kicking plate inner
7.
Rear pillar finisher
8.
Rear body side welt
9.
Rear kicking plate outer
10. Center pillar upper garnish
Pawl
Metal clip
Clip
⇐
Vehicle front
SIIA0810E
BODY SIDE TRIM
INT-21
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
FRONT PILLAR GARNISH
Removal
Release the clips, then remove front pillar garnish.
Installation
Installation is in the reverse order of removal.
FRONT KICKING PLATE INNER
Removal
Release the clips, then remove front kicking plate inner.
Installation
Installation is in the reverse order of removal.
FRONT KICKING PLATE OUTER
Removal
Release the clips, then remove front kicking plate outer.
Installation
PIIB2600J
PIIB2569J
PIIB2570J
PIIB2571J
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст