Nissan Tiida C11. Instruction — part 926
INT-22
< ON-VEHICLE REPAIR >
BODY SIDE TRIM
Installation is in the reverse order of removal.
REAR KICKING PLATE INNER
Removal
Release the clips, then remove rear kicking plate inner.
Installation
Installation is in the reverse order of removal.
REAR KICKING PLATE OUTER
Removal
Release the clips, then remove rear kicking plate outer.
Installation
Installation is in the reverse order of removal.
CENTER PILLAR LOWER GARNISH
Removal
1.
Remove front kicking plate inner. Refer to "FRONT KICKING PLATE INNER".
2.
Remove rear kicking plate inner. Refer to "REAR KICKING PLATE INNER".
3.
Remove front and rear body side welts.
4.
Release the clips, then remove center pillar lower garnish.
Installation
Installation is in the reverse order of removal.
CENTER PILLAR UPPER GARNISH
Removal
WARNING:
PIIB2573J
PIIB2572J
PIIB2574J
BODY SIDE TRIM
INT-23
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
Do not reuse center pillar upper garnish if removed.
1.
Remove center pillar lower garnish. Refer to "CENTER PILLAR LOWER GARNISH".
2.
Remove front seat belt shoulder anchor. Refer to
"Removal and Installation of Front Seat Belt"
.
3.
Remove front and rear body side welts.
4.
Release the resin clips, then remove center pillar upper garnish.
Installation
Installation is in the reverse order of removal.
REAR PILLAR FINISHER
Removal
1.
Remove rear seat cushion, rear seatback, and seatback side cushions. Refer to
.
2.
Remove rear body side welt.
3.
Release the clips, then remove rear pillar finisher.
Installation
Installation is in the reverse order of removal.
PIIB2575J
INT-24
< ON-VEHICLE REPAIR >
LUGGAGE FLOOR TRIM
LUGGAGE FLOOR TRIM
Removal and Installation
INFOID:0000000001329113
REMOVAL
CAUTION:
1.
Luggage side lower finisher RH
2.
Access cover
3.
Shock absorber cover RH
4.
Luggage floor center board
5.
Tonneau board
6.
Luggage side lower finisher LH
7.
Cargo lamp
8.
Shock absorber cover LH
9.
Luggage rear plate
10. Striker cover plate
Pawl
Metal clip
Clip C101
⇐
Vehicle front
AWJIA0062ZZ
LUGGAGE FLOOR TRIM
INT-25
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
• Insert a trim stick or suitable tool between panel on vehicle
and clips (as indicated with arrow) to release clips.
• Use a trim stick or suitable tool when removing metal clips
from garnishes.
• Be careful not to damage the body while prying to release
clips.
• Make sure clips are properly aligned in panel holes on body
when installing, then press them in completely.
1.
Disconnect the negative and positive battery cables.
2.
Open the rear doors and the back door.
3.
Remove the rear seat cushion and seatback and seatback side
RH/LH. Refer to
SE-18, "Removal and Installation"
.
4.
Lift and remove the luggage floor center board.
5.
Detach the tethers, then pull upward to remove the tonneau board.
6.
Release the clips, then remove the striker cover and luggage rear plate.
7.
Release the clips, then remove the luggage side lower finisher RH/LH.
• For LH side, disconnect cargo lamp connector.
INSTALLATION
Installation is in the reverse order of removal.
SIIA0810E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст