Nissan Tiida C11. Instruction — part 1424
VTL-32
< FUNCTION DIAGNOSIS >
[MANUAL AIR CONDITIONER]
AIR CONDITIONER FILTER
FUNCTION DIAGNOSIS
AIR CONDITIONER FILTER
Description
INFOID:0000000001710935
FUNCTION
The fresh air (A) and the recirculated air (B) drawn inside the pas-
senger compartment by the front blower motor (1) is kept clean (C)
on either mode by the air conditioner filter (2), located before the
evaporator (3), in the A/C unit assembly.
WJIA2253E
AIR CONDITIONER FILTER
VTL-33
< ON-VEHICLE MAINTENANCE >
[MANUAL AIR CONDITIONER]
C
D
E
F
G
H
J
K
L
M
A
B
VTL
N
O
P
ON-VEHICLE MAINTENANCE
AIR CONDITIONER FILTER
Removal and Installation
INFOID:0000000001710936
REPLACEMENT TIMING
Replace the air conditioner filter according to the maintenance schedules. Refer to
NOTE:
The air conditioner filter caution label is located inside the glove box door.
REPLACEMENT PROCEDURES
1.
Remove the instrument lower finisher and instrument lower cover (LH) for LHD only. Refer to
2.
Remove the glove box assembly and instrument lower cover (RH) for RHD only. Refer to
3.
Compress the air conditioner filter (1) downward while sliding it
to the RH side of the vehicle to release the upper pawl.
4.
Move the bottom of air conditioner filter (1) upward as shown to
release the bottom tab, then remove it.
5.
Replace the air conditioner filter with new one and install the new filter in the A/C unit assembly.
CAUTION:
Make sure that the air conditioner filter lower tab is fully seated, and that the air conditioner upper
pawl is locked into place securing the new filter into the A/C unit assembly.
6.
Install the glove box assembly and instrument lower cover (RH) for RHD only. Refer to
7.
Install the instrument lower finisher and instrument lower cover (LH) for LHD only. Refer to
SJIA0652E
VTL-34
< ON-VEHICLE REPAIR >
[MANUAL AIR CONDITIONER]
CONTROLLER
ON-VEHICLE REPAIR
CONTROLLER
Removal and Installation
INFOID:0000000001696528
REMOVAL
1.
Remove cluster lid C and instrument finisher D. Refer to
IP-11, "Removal and Installation"
2.
Remove intake door lever knob. Refer to
.
3.
Remove mounting screws and clips, and then remove controller
finisher.
4.
Remove mounting screws, and then pull out controller.
5.
Remove instrument panel and pad. Refer to
IP-11, "Removal and Installation"
.
6.
Remove air mix door cable, mode door cable and intake door cable from A/C unit assembly.
7.
Disconnect connector, and then remove controller.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
Adjust the door cables during installation. Refer to
VTL-45, "Intake Door Cable Adjustment"
,
VTL-46, "Air Mix Door Cable Adjustment"
.
ZJIA0697E
ZJIA0698E
CONTROLLER
VTL-35
< ON-VEHICLE REPAIR >
[MANUAL AIR CONDITIONER]
C
D
E
F
G
H
J
K
L
M
A
B
VTL
N
O
P
Disassembly and Assembly
INFOID:0000000001696529
CAUTION:
Install inner cable of each door cable to the corresponding
lever, as shown in the figure. Press outer cable until it hooks on
the tabs and becomes secure.
1.
Air mix door cable
2.
Intake door cable
3.
Mode door cable
4.
A/C controller assembly
5.
Mode control dial
6.
Rear DEF button
7.
A/C button
8.
Temperature control dial
9.
Illumination bulb
10. Intake door lever knob
11.
Fan control dial
ZJIA0106J
MJIA0038E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст