Nissan Tiida C11. Instruction — part 708
EM-184
< ON-VEHICLE REPAIR >
[MR18DE]
TIMING CHAIN
Be sure O-rings a aligned properly.
13. Apply the sealant without breaks to the specified location using
Tool.
Use Genuine Silicone RTV Sealant or equivalent. Refer to
GI-27, "Recommended Chemical Products and Sealants"
.
14. Make sure that matching marks of timing chain and each sprocket are still aligned.
CAUTION:
• Make sure O-ring on cylinder block is correctly installed.
• Be careful not to damage front oil seal by interference with front end of crankshaft.
15. Install front cover, and tighten bolts in numerical order as shown.
CAUTION:
Attaching should be done within 5 minutes after liquid gas-
ket application.
NOTE:
Follow the installation position of bolts as shown.
16. Tighten all bolts are in two stages to specified torque in numeri-
cal order as shown.
CAUTION:
Be sure to wipe off any excessive liquid gasket leaking.
17. Install crankshaft pulley.
CAUTION:
• Never damage front oil seal lip section.
• If needed use a plastic hammer, tap on its center portion (not circumference) to seat crankshaft
pulley.
Tool number
WS39930000 (
–
)
A
: Liquid gasket application area
: Engine outside
PBIC3959E
M6 bolts
:
No. 1
M10 bolts
:
No. 6, 7, 10, 11, 14
M12 bolts
:
No. 2, 4, 8, 12
M8 bolts
:
Except the above
PBIC3164J
TIMING CHAIN
EM-185
< ON-VEHICLE REPAIR >
[MR18DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
18. Secure crankshaft pulley (1) using tool (A).
19. Apply new engine oil to thread and seat surfaces of crankshaft
pulley bolt.
20. Tighten crankshaft pulley bolt in three steps.
21. Put a paint mark (B) on crankshaft pulley (2), matching with any
one of six easy to recognize angle marks (A) on crankshaft pul-
ley bolt (1) flange.
22. Turn another 60 degrees clockwise (angle tightening) using
Tool.
• Check the tightening angle with movement of one angle mark.
23. Make sure that crankshaft rotates clockwise smoothly.
24. Installation of the remaining components is in the reverse order of removal.
Step 1
: 68.6 N·m (7.0 kg-m, 51 ft-lb)
Step 2
: 0 N·m (0 kg-m, 0 ft-lb)
Step 3
: 29.4 N·m (3.0 kg-m, 22 ft-lb)
PBIC3961E
Tool number
: KV10112100 (BT-8653-A)
PBIC3963E
EM-186
< ON-VEHICLE REPAIR >
[MR18DE]
CAMSHAFT
CAMSHAFT
Component
INFOID:0000000001337797
Removal and Installation
INFOID:0000000001337798
REMOVAL
WARNING:
• Put a “CAUTION: FLAMMABLE” sign in the workshop.
• Be sure to work in a well ventilated area and furnish workshop with a CO
2
fire extinguisher.
• Do not smoke while servicing fuel system. Keep open flames and sparks away from the work area.
1.
Release the fuel pressure. Refer to
.
2.
Disconnect negative battery cable. Refer to
PG-6, "Removal and Installation"
3.
Remove front RH wheel. Refer to
.
4.
Remove front fender protector (RH). Refer to
EXT-22, "Removal and Installation"
5.
Drain engine coolant. Refer to
CO-35, "Changing Engine Coolant"
.
NOTE:
Perform this step when engine is cold.
6.
Remove the following parts.
• Intake manifold; Refer to
• Rocker cover; Refer to
EM-173, "Removal and Installation"
1.
O-ring
2.
Camshaft position sensor (PHASE)
3.
Camshaft bracket
4.
Camshaft sprocket (EXH)
5.
Camshaft sprocket (INT)
6.
Camshaft (EXH)
7.
Camshaft (INT)
8.
Valve lifter (EXH)
9.
Valve lifter (INT)
10. Cylinder head
A.
.
PBIC4589E
CAMSHAFT
EM-187
< ON-VEHICLE REPAIR >
[MR18DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
• Fuel tube and fuel injector assembly; Refer to
• Front cover, timing chain and related parts; Refer to
.
7.
Remove camshaft position sensor (PHASE) from camshaft bracket.
CAUTION:
• Handle carefully to avoid dropping and shocks.
• Never disassemble.
• Never allow metal powder to adhere to magnetic part at sensor tip.
• Never place sensor in a location where it is exposed to magnetism.
8.
Put the matching mark (A) on the camshaft sprocket (INT) (2)
and the camshaft bracket (1) as shown.
NOTE:
It prevents the knock pin of the camshaft (INT) from engaging
with the incorrect pin hole when installing the camshaft sprocket
(INT).
9.
Remove camshaft sprockets (INT) (1) and (EXH) (2).
• Secure hexagonal part (A) of camshaft with a wrench. Loosen
camshaft sprocket bolts and remove camshaft sprocket.
CAUTION:
• Never rotate crankshaft or camshaft while timing chain
is removed. It causes interference between valve and
piston.
• Never loosen the bolts with securing anything other
than the camshaft hexagonal part or with tensioning the
timing chain.
10. Loosen bolts in reverse order as shown.
11. Cut liquid gasket by prying the position (
) shown, and then
remove the camshaft bracket.
CAUTION:
• Be careful not to damage the mating surface.
• A more adhesive liquid gasket is applied compared to pre-
vious types when shipped, so it should not be forced off
the position not specified.
12. Remove camshafts.
: Engine front
PBIC3992J
PBIC3454J
: Engine front
PBIC3176J
: Engine front
PBIC3358J
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст