Nissan Tiida C11. Instruction — part 1349
SYSTEM SYMPTOM
TM-447
< SYMPTOM DIAGNOSIS >
[TYPE 2 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
1.
Remove oil pan. Refer to
2.
Check A/T fluid condition. Refer to
.
OK or NG
OK
>> GO TO 7.
NG
>> GO TO 5.
7.
CHECK SYMPTOM
OK or NG
OK
>> INSPECTION END
NG
>> GO TO 8.
8.
CHECK TCM
1.
Check TCM input/output signals. Refer to
TM-22, "Input/Output Signal of TCM"
2.
If NG, recheck TCM pin terminals for damage or loose connection with harness connector.
OK or NG
OK
>> INSPECTION END
NG
>> Repair or replace damaged parts.
Vehicle Cannot Be Started from D
1
INFOID:0000000001714353
SYMPTOM:
Vehicle cannot be started from D
1
on “Cruise Test — Part 1”.
1.
CHECK SYMPTOM
Check symptom. Refer to
.
Is “Vehicle Dose Not Creep Backward in “R” Position” OK?
OK
>> GO TO 2.
NG
>> GO TO
TM-444, "Vehicle Does Not Creep Backward in "R" Position"
.
2.
CHECK SELF-DIAGNOSTIC RESULTS
Perform self-diagnosis. Refer to
XX-XX, "*****"
or
TM-38, "Diagnosis Procedure without CONSULT-III"
.
Is any malfunction detected by self-diagnostic results?
YES
>> Check the malfunctioning system. Refer to
XX-XX, "*****"
or
XX-XX, "*****"
.
NO
>> GO TO 3.
3.
CHECK ACCELERATOR PEDAL POSITION SENSOR
Check accelerator pedal position sensor. Refer to
XX-XX, "*****"
(type 1) or
XX-XX, "*****"
(type 2).
OK or NG
OK
>> GO TO 4.
NG
>> Repair or replace accelerator pedal position sensor.
4.
CHECK LINE PRESSURE
Check line pressure at stall point with selector lever in “D” position. Refer to
OK or NG
OK
>> GO TO 6.
NG
>> GO TO 5.
5.
DETECT MALFUNCTIONING ITEM
1.
Remove control valve assembly. Refer to
TM-191, "Control Valve Assembly and Accumulators"
2.
Check the following items:
-
Shift valve A
-
Shift valve B
-
Shift solenoid valve A
-
Shift solenoid valve B
-
Pilot valve
-
Pilot filter
TM-448
< SYMPTOM DIAGNOSIS >
[TYPE 2 (4AT: RE4F03B)]
SYSTEM SYMPTOM
3.
Disassemble A/T. Refer to
4.
Check the following items:
-
Forward clutch assembly. Refer to
TM-267, "Forward and Overrun Clutches"
.
-
Low one-way clutch. Refer to
-
Forward one-way clutch. Refer to
TM-278, "Rear Internal Gear and Forward Clutch Hub"
.
-
High clutch assembly. Refer to
.
-
Torque converter. Refer to
-
Oil pump assembly. Refer to
OK or NG
OK
>> GO TO 8.
NG
>> Repair or replace damaged parts.
6.
CHECK A/T FLUID CONDITION
1.
Remove oil pan. Refer to
2.
Check A/T fluid condition. Refer to
.
OK or NG
OK
>> GO TO 7.
NG
>> GO TO 5.
7.
DETECT MALFUNCTIONING ITEM
1.
Remove control valve assembly. Refer to
TM-191, "Control Valve Assembly and Accumulators"
2.
Check the following items:
-
Shift valve A
-
Shift valve B
-
Shift solenoid valve A
-
Shift solenoid valve B
-
Pilot valve
-
Pilot filter
OK or NG
OK
>> GO TO 8.
NG
>> Repair or replace damage parts.
8.
CHECK SYMPTOM
Check again. Refer to
TM-183, "Cruise Test - Part 1"
OK or NG
OK
>> INSPECTION END
NG
>> GO TO 9.
9.
CHECK TCM
1.
Check TCM input/output signals. Refer to
TM-22, "Input/Output Signal of TCM"
2.
If NG, recheck TCM pin terminals for damage or loose connection with harness connector.
OK or NG
OK
>> INSPECTION END
NG
>> Repair or replace damaged parts.
A/T Does Not Shift: D
1
→
D
2
or Does Not Kickdown: D
4
→
D
2
INFOID:0000000001714354
SYMPTOM:
A/T does not shift from D
1
to D
2
at the specified speed on “Cruise Test — Part 1”.
A/T does not shift from D
4
to D
2
when depressing accelerator pedal fully at the specified speed on
“Cruise Test — Part 2”.
1.
CHECK SYMPTOM
Check symptom. Refer to
TM-183, "Cruise Test - Part 1"
Are “Vehicle Dose Not Creep Forward in “D”, “2” or “1” Position” and “Vehicle Cannot Be Started from D
1
” OK?
YES
>> GO TO 2.
NG
TM-446, "Vehicle Does Not Creep Forward in "D", "2" or "1" Position"
and
SYSTEM SYMPTOM
TM-449
< SYMPTOM DIAGNOSIS >
[TYPE 2 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
2.
CHECK A/T POSITION
Check A/T position. Refer to
TM-204, "Checking of A/T Position"
OK or NG
OK
>> GO TO 3.
NG
>> Adjust A/T position. Refer to
TM-204, "Adjustment of A/T Position"
.
3.
CHECK VEHICLE SPEED SENSOR·A/T AND VEHICLE SPEED SENSOR·MTR CIRCUIT
Check vehicle speed sensor·A/T (revolution sensor) and vehicle speed sensor·MTR circuit. Refer to
XX-XX,
"*****"
(type 1) or
XX-XX, "*****"
(type 2) and
XX-XX, "*****"
(type 1) or
XX-XX, "*****"
(type 2).
OK or NG
OK
>> GO TO 4.
NG
>> Repair or replace vehicle speed sensor·A/T (revolution sensor) and vehicle speed sensor·MTR
circuits.
4.
CHECK ACCELERATOR PEDAL POSITION SENSOR
Check accelerator pedal position sensor. Refer to
XX-XX, "*****"
(type 1) or
XX-XX, "*****"
(type 2).
OK or NG
OK
>> GO TO 5.
NG
>> Repair or replace accelerator pedal position sensor.
5.
CHECK A/T FLUID CONDITION
1.
Remove oil pan. Refer to
2.
Check A/T fluid condition. Refer to
.
OK or NG
OK
>> GO TO 7.
NG
>> GO TO 6.
6.
DETECT MALFUNCTIONING ITEM
1.
Remove control valve. Refer to
TM-191, "Control Valve Assembly and Accumulators"
.
2.
Check the following items:
-
Shift valve A
-
Shift valve B
-
Shift solenoid valve A
-
Shift solenoid valve B
-
Pilot valve
-
Pilot filter
3.
Disassemble A/T. Refer to
4.
Check the following items:
-
Servo piston assembly
-
Brake band
OK or NG
OK
>> GO TO 8.
NG
>> Repair or replace damaged parts.
7.
DETECT MALFUNCTIONING ITEM
1.
Remove control valve. Refer to
TM-191, "Control Valve Assembly and Accumulators"
.
2.
Check the following items:
-
Shift valve A
-
Shift valve B
-
Shift solenoid valve A
-
Shift solenoid valve B
-
Pilot valve
-
Pilot filter
OK or NG
OK
>> GO TO 8.
NG
>> Repair or replace damaged parts.
TM-450
< SYMPTOM DIAGNOSIS >
[TYPE 2 (4AT: RE4F03B)]
SYSTEM SYMPTOM
8.
CHECK SYMPTOM
Check again. Refer to
TM-183, "Cruise Test - Part 1"
TM-185, "Cruise Test - Part 2"
.
OK or NG
OK
>> INSPECTION END
NG
>> GO TO 9.
9.
CHECK TCM
1.
Check TCM input/output signals. Refer to
TM-22, "Input/Output Signal of TCM"
2.
If NG, recheck TCM pin terminals for damage or loose connection with harness connector.
OK or NG
OK
>> INSPECTION END
NG
>> Repair or replace damaged parts.
A/T Does Not Shift: D
2
→
D
3
INFOID:0000000001714355
SYMPTOM:
A/T does not shift from D
2
to D
3
at the specified speed on “Cruise Test — Part 1” and “Cruise Test —
Part 2”.
1.
CHECK SYMPTOM
Check symptom. Refer to
TM-183, "Cruise Test - Part 1"
Are “Vehicle Does Not Creep Forward in “D”, “2” or “1” Position” and “Vehicle Cannot Be Started from D
1
” OK?
YES
>> GO TO 2.
NO
>> Go to
TM-446, "Vehicle Does Not Creep Forward in "D", "2" or "1" Position"
and
2.
CHECK A/T POSITION
Check A/T position. Refer to
TM-204, "Checking of A/T Position"
OK or NG
OK
>> GO TO 3.
NG
>> Adjust A/T position. Refer to
TM-204, "Adjustment of A/T Position"
.
3.
CHECK VEHICLE SPEED SENSOR·A/T AND VEHICLE SPEED SENSOR·MTR CIRCUIT
Check vehicle speed sensor·A/T (revolution sensor) and vehicle speed sensor·MTR circuit. Refer to
XX-XX,
"*****"
(type 1) or
XX-XX, "*****"
(type 2) and
XX-XX, "*****"
(type 1) or
XX-XX, "*****"
(type 2).
OK or NG
OK
>> GO TO 4.
NG
>> Repair or replace vehicle speed sensor·A/T (revolution sensor) and vehicle speed sensor·MTR
circuits.
4.
CHECK ACCELERATOR PEDAL POSITION SENSOR
Check accelerator pedal position sensor. Refer to
XX-XX, "*****"
(type 1) or
XX-XX, "*****"
(type 2).
OK or NG
OK
>> GO TO 5.
NG
>> Repair or replace accelerator pedal position sensor.
5.
CHECK A/T FLUID CONDITION
1.
Remove oil pan. Refer to
2.
Check A/T fluid condition. Refer to
.
OK or NG
OK
>> GO TO 7.
NG
>> GO TO 6.
6.
DETECT MALFUNCTIONING ITEM
1.
Remove control valve assembly. Refer to
TM-191, "Control Valve Assembly and Accumulators"
2.
Check the following items:
-
Shift valve B
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст