Nissan Tiida C11. Instruction — part 1371
REPAIR FOR COMPONENT PARTS
TM-535
< DISASSEMBLY AND ASSEMBLY >
[TYPE 2 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
• Measure side clearance of inner gear and outer gear in at least
four places around each outside edge. Maximum measured values
should be within the specified clearance.
• If clearance is less than standard, select inner gear and outer gear
as a set so that clearance is within specifications.
• If clearance is more than standard, replace whole oil pump assem-
bly except oil pump cover.
• Measure clearance between outer gear and oil pump housing.
• If not within allowable limit, replace whole oil pump assembly
except oil pump cover.
Seal Ring Clearance
• Measure clearance between seal ring and ring groove.
• If not within allowable limit, replace oil pump cover assembly.
ASSEMBLY
Standard clearance:
.
SCIA4957E
Standard clearance and allowable limit:
SAT096D
Standard clearance and allowable limit:
SAT097D
TM-536
< DISASSEMBLY AND ASSEMBLY >
[TYPE 2 (4AT: RE4F03B)]
REPAIR FOR COMPONENT PARTS
1.
Install oil pump housing oil seal on oil pump housing.
CAUTION:
• Do not reuse oil pump housing oil seal.
• Apply ATF to outer surface of oil pump housing oil seal.
2.
Install inner gear and outer gear on oil pump housing.
CAUTION:
Be careful with the direction of inner gear.
3.
Install oil pump cover on oil pump housing.
a.
Wrap masking tape around splines of oil pump cover assembly
to protect seal. Position oil pump cover assembly on oil pump
housing assembly, then remove masking tape.
b.
Tighten oil pump cover fitting bolts in the order as shown, and
then tighten them to the specified torque in the same order.
4.
Install seal rings (1) to oil pump assembly (2) carefully after
packing ring groove with petroleum jelly.
CAUTION:
Do not spread gap of seal rings (1) excessively while install-
ing. The seal rings (1) may be deformed.
Control Valve Assembly
INFOID:0000000001731437
COMPONENTS
SAT900DA
SAT092D
SAT101D
SCIA7016E
REPAIR FOR COMPONENT PARTS
TM-537
< DISASSEMBLY AND ASSEMBLY >
[TYPE 2 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
DISASSEMBLY
Place control valve assembly with control valve upper body (1) side
down. Remove bolts (A) to (G), reamer bolts (F), nuts and support
plates (4) according to the following procedures. Separate control
valve upper body (1), control valve inter body (2) and control valve
lower body (3).
1.
Pilot filter
2.
Control valve upper body
3.
Steel ball
4.
Separating plate
5.
Control valve inter body
6.
Steel ball
7.
Support plate
8.
Separating plate
9.
Control valve lower body
10. Line pressure relief valve spring
11.
Check ball
12. Torque converter pressure holding
spring
13. Solenoid valve assembly
14. Terminal body
15. O-ring
16. O-ring
17. O-ring
18. Oil strainer
SCIA5967J
SCIA7058E
TM-538
< DISASSEMBLY AND ASSEMBLY >
[TYPE 2 (4AT: RE4F03B)]
REPAIR FOR COMPONENT PARTS
Bolt length, number and location:
*
: Reamer bolt and nut.
1.
Remove bolts (A), (D), reamer bolt (F) and nut, and remove oil
strainer (1) from control valve assembly.
2.
Remove bolts (A), (C) and (G), and then remove solenoid valve
assembly (1) from control valve assembly.
3.
Remove O-rings from solenoid valves and terminal body.
4.
Place control valve upper body face down, and remove bolts
(B), reamer bolt (F) and nut.
CAUTION:
Remove bolts with control valve upper body facing down,
because control valve upper body and control valve inter
body may come off and steel ball may fall and be lost.
Bolt symbol
A
B
C
D
E
F
*
G
Bolt length “
” [mm (in)]
13.5
(0.531)
58.0
(2.283)
40.0
(1.575)
66.0
(2.598)
33.0
(1.299)
78.0
(3.071)
18.0
(0.709)
Number of bolts
6
3
6
11
2
2
1
SCIA7007E
SCIA7008E
SCIA7180E
ATL0020D
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст