Nissan Tiida C11. Instruction — part 832
HIGH-PRESSURE PIPE
HA-43
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
J
K
L
M
A
B
HA
N
O
P
HIGH-PRESSURE PIPE
Removal and Installation of High-Pressure Pipe - MR18DE, HR16DE
INFOID:0000000001404219
REMOVAL
1.
Remove low-pressure flexible hose. Refer to
HA-38, "Removal and Installation of Low-Pressure Flexible
.
2.
Remove high-pressure pipe from the clips.
3.
Remove high-pressure pipe bolt (A), and then remove high-
pressure pipe (1) from condenser (2).
CAUTION:
Cap or wrap the joint of the pipe with suitable material such
as vinyl tape to avoid the entry of air.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Replace O-rings of high-pressure pipe with a new ones, and apply compressor oil when installing.
• When recharging refrigerant, check for leaks. Refer to
HA-22, "Checking of Refrigerant Leaks"
Removal and Installation of High-Pressure Pipe - K9K
INFOID:0000000001527625
REMOVAL
1.
Use the recovery/recycling equipment to evacuate the refrigerant. Refer to
2.
Remove engine cover.
3.
Remove cowl top cover. Refer to
EXT-20, "Removal and Installation"
.
4.
Reposition the lower dash insulator out of the way.
5.
Remove the front grille. Refer to
EXT-19, "Removal and Installation"
6.
Reposition the RH air guide out of the way.
1.
High-pressure pipe
A.
High-pressure pipe clips
SJIA0679E
SJIA0680E
HA-44
< ON-VEHICLE REPAIR >
HIGH-PRESSURE PIPE
7.
Remove bolt (A), and then disconnect the low-pressure pipe (1)
and high-pressure pipe (2) from the expansion valve.
CAUTION:
Cap or wrap the joint of the pipe with suitable material such
as vinyl tape to avoid the entry of air.
8.
Disconnect the high-pressure pipe from the condenser.
CAUTION:
Cap or wrap the joint of the pipe with suitable material such as vinyl tape to avoid the entry of air.
9.
Remove the upper torque rod. Refer to
.
10. Disconnect the high-pressure pipe from the clips.
11. Remove the high-pressure pipe.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Replace O-rings for A/C piping with new ones, and apply compressor oil when installing.
• When charging the refrigerant, check for leaks. Refer to
HA-22, "Checking of Refrigerant Leaks"
SJIA0644E
CONDENSER
HA-45
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
J
K
L
M
A
B
HA
N
O
P
CONDENSER
Removal and Installation of Condenser - MR18DE, HR16DE
INFOID:0000000001527646
REMOVAL
1.
Use the recovery/recycling equipment to evacuate the refrigerant. Refer to
2.
Remove the three upper headlamp bolts to reposition the headlamps out of the way
3.
Remove the radiator core support upper.
4.
Disconnect the high-pressure flexible hose and high-pressure pipe from condenser.
CAUTION:
Cap or wrap the joint of the pipe with suitable material such as vinyl tape to avoid the entry of air.
5.
Disconnect refrigerant pressure sensor connector.
6.
Tilt radiator toward rear of vehicle, and then remove condenser
(1) from between radiator and radiator core support upper.
CAUTION:
Be careful not to damage the core surface of condenser and
radiator.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Replace O-rings for A/C piping with new ones, and apply compressor oil when installing.
• When recharging refrigerant, check for leaks. Refer to
HA-22, "Checking of Refrigerant Leaks"
Removal and Installation for Condenser - K9K
INFOID:0000000001527627
REMOVAL
1.
Use the recovery/recycling equipment to evacuate the refrigerant. Refer to
2.
Remove the air duct (front).
3.
Remove the radiator core support finisher.
4.
Remove the front grille. Refer to
EXT-19, "Removal and Installation"
5.
Remove the lower splash shield.
6.
Remove the radiator core support upper.
7.
Disconnect the high-pressure pipe from the condenser.
CAUTION:
Cap or wrap the joint of the pipe with suitable material such as vinyl tape to avoid the entry of con-
taminants.
8.
Disconnect the high-pressure flexible hose from the condenser.
CAUTION:
Cap or wrap the joint of the pipe with suitable material such as vinyl tape to avoid the entry of con-
taminants.
9.
Disconnect the refrigerant pressure sensor connector and remove the refrigerant pressure sensor.
10. Remove the four condenser bolts.
11. Remove the condenser.
CAUTION:
Do not damage the condenser fins
SJIA0682E
HA-46
< ON-VEHICLE REPAIR >
CONDENSER
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not damage the condenser fins.
• Replace O-rings of the high-pressure pipe, high-pressure flexible hose and refrigerant pressure sen-
sor with new ones, and apply compressor oil when installing.
• When charging the refrigerant, check for leaks. Refer to
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст