Nissan Tiida C11. Instruction — part 1381
REPAIR FOR COMPONENT PARTS
TM-575
< DISASSEMBLY AND ASSEMBLY >
[TYPE 2 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
DISASSEMBLY
1.
Remove seal rings from output shaft and bearing retainer.
1.
Idler gear
2.
Idler gear bearing
3.
Reduction pinion gear adjusting
shim
4.
Reduction pinion gear bearing
5.
Reduction pinion gear
6.
Output shaft bearing
7.
Seal ring
8.
Bearing retainer
9.
Output shaft
10. Seal ring
11.
Output gear adjusting spacer
12. Output gear bearing
13. Output gear
14. Lock nut
SCIA5883J
SAT666D
TM-576
< DISASSEMBLY AND ASSEMBLY >
[TYPE 2 (4AT: RE4F03B)]
REPAIR FOR COMPONENT PARTS
2.
Remove output shaft bearing according to the following proce-
dures.
a.
Set output shaft bearing inner race (1) on suitable tool (A), and
set a suitable tool (B) on output shaft (2), and press output shaft
(2) to remove output shaft bearing inner race (1).
CAUTION:
Set a drift (A) on output shaft bearing inner race (1).
b.
Set Tool on output shaft bearing outer race, and remove output
shaft bearing outer race from bearing retainer.
3.
Remove output gear bearing according to the following proce-
dures.
a.
Insert suitable tool (A) between the mating surfaces of output
gear (1) and output gear bearing inner race (2), and enlarge the
gap.
CAUTION:
Do not damage output gear (1).
b.
Set a suitable tool (B) on output gear (1), and remove output
gear bearing inner race (2) using suitable tool (C).
c.
Set Tool (A) on output gear bearing outer race (1), and remove
output gear bearing outer race (1) from bearing retainer (2).
4.
Remove idler gear bearing according to the following proce-
dures.
a.
Insert suitable tool (A) between the mating surfaces of idler gear
(1) and idler gear bearing inner race (2), and enlarge the gap.
CAUTION:
Do not damage idler gear (1).
b.
Set suitable tool (B), on idler gear (1), and remove idler gear
bearing inner race (2) using suitable tool (C).
SCIA7041E
SAT168K
SCIA7042E
Tool number:
KV381054S0
SCIA7043E
SCIA7044E
REPAIR FOR COMPONENT PARTS
TM-577
< DISASSEMBLY AND ASSEMBLY >
[TYPE 2 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
c.
Set Tool on idler gear bearing outer race, and remove idler gear
bearing outer race from transaxle case.
5.
Remove reduction pinion gear bearing according to the following
procedures.
a.
Set Tool on reduction pinion gear bearing inner race, and press
reduction pinion gear to remove reduction pinion gear bearing
inner race.
CAUTION:
Set Tool on reduction pinion gear bearing inner race.
b.
Remove reduction pinion gear bearing outer race from transaxle
case.
INSPECTION
Output Shaft, Output Gear, Idler Gear and Reduction Pinion Gear
Check for wear, damage or crack. Replace if necessary.
Bearings
• Make sure bearings roll freely and are free from noise, cracks, pitting or wear.
• When replacing taper roller bearing, replace outer and inner race as a set.
Check for damage or deformation. Replace if necessary.
Seal Ring Clearance
• Install new seal rings (1) on output shaft (2).
• Measure clearance “A” between each seal ring and groove.
• Replace output shaft (2) if the measurements exceed the allowable
limit.
• Install new seal rings (1) on bearing retainer (3).
• Measure clearance “A” between each seal ring and groove.
• Replace bearing retainer (3) if the measurements exceed the allowable limit.
SAT859DD
NAT048
SAT651D
Standard clearance and allowable limit:
Standard clearance and allowable limit:
.
SCIA7045E
TM-578
< DISASSEMBLY AND ASSEMBLY >
[TYPE 2 (4AT: RE4F03B)]
REPAIR FOR COMPONENT PARTS
ASSEMBLY
1.
Install reduction pinion gear bearing according to the following
procedures.
a.
Set Tool on reduction pinion gear bearing inner race, and press
reduction pinion gear to reduction pinion gear bearing inner
race.
CAUTION:
Set Tool on reduction pinion gear bearing inner race.
b.
Install reduction pinion gear bearing outer race to transaxle
case.
c.
Tighten reduction pinion gear bearing outer race bolts to the
specified torque.
2.
Checking reduction pinion gear bearing preload. Refer to
3.
Install idler gear bearing according to the following procedures.
CAUTION:
Do not reuse idler gear bearing.
a.
Set Tool (A) and suitable tool (B) on idler gear bearing inner race
(1), and press idler gear bearing inner race (1) to idler gear (2).
CAUTION:
Set Tool (A) on idler gear bearing inner race (1).
b.
Set Tool on idler gear bearing outer race, and drive idler gear
bearing outer race into transaxle case.
NAT049
SAT651D
Tool number:
KV35272000
SCIA7046E
NAT051
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст