Nissan Tiida C11. Instruction — part 1382
REPAIR FOR COMPONENT PARTS
TM-579
< DISASSEMBLY AND ASSEMBLY >
[TYPE 2 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
4.
Install output shaft bearing according to the following proce-
dures.
a.
Set suitable tool (A) and a suitable tool (B) on output shaft bear-
ing inner race (1), and press output shaft (2) to output shaft
bearing inner race (1).
CAUTION:
Set suitable tool (A) on output shaft bearing inner race (1).
b.
Set Tool on output shaft bearing outer race, and drive output
shaft bearing outer race to bearing retainer.
5.
Checking output shaft bearing preload. Refer to
.
6.
Install seal rings according to the following procedures.
a.
Install seal rings (1) evenly to the grooves on output shaft (2)
and bearing retainer (3), and fully close the opening.
CAUTION:
Roll paper around seal rings to prevent seal rings from
spreading.
SCIA7048E
SCIA0270E
SCIA7049E
SCIA2190E
TM-580
< DISASSEMBLY AND ASSEMBLY >
[TYPE 2 (4AT: RE4F03B)]
REPAIR FOR COMPONENT PARTS
7.
Install output gear bearing according to the following proce-
dures.
CAUTION:
Do not reuse output gear bearing.
a.
Set Tool (A) and suitable (B) on output gear bearing inner race
(1), and press output gear bearing inner race (1) to output gear
(2).
CAUTION:
Set Tool (A) on output gear bearing inner race (1).
b.
Set Tool on output gear bearing outer race, and drive output
gear bearing outer race to bearing retainer.
Band Servo Piston Assembly
INFOID:0000000001731446
COMPONENTS
DISASSEMBLY
Tool number:
KV35272000
SCIA7047E
SCIA0268E
1.
Lock nut
2.
Anchor end pin
3.
O-ring
4.
Servo piston retainer
5.
D-ring
6.
OD servo piston
7.
O-ring
8.
Snap ring
9.
OD servo piston retainer
10. E-ring
11.
Spring retainer
12. OD servo return spring
13. D-ring
14. Band servo piston
15. Band servo thrust washer
16. Band servo piston stem
17. 2nd servo return spring
SCIA5891J
REPAIR FOR COMPONENT PARTS
TM-581
< DISASSEMBLY AND ASSEMBLY >
[TYPE 2 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
1.
Push in OD servo piston assembly using suitable tool (A) and
suitable tool (B), and then remove snap ring (1) from transaxle
case using suitable tool (C).
2.
Apply compressed air into the oil hole as shown to remove OD
servo piston assembly and band servo piston assembly.
CAUTION:
Do not blow air in too quickly, or OD servo piston assembly,
band servo piston assembly and ATF could jump out. Care-
fully blow air little by little while protecting with lint-free
cloth A.
3.
Remove 2nd servo return spring from transaxle case.
4.
Wrap OD servo piston retainer (1) using lint-free cloth A, and
then apply compressed air into the band servo piston stem hole
on OD servo piston (2) to remove OD servo piston (2) from OD
servo piston retainer (1).
CAUTION:
Do not blow air in too quickly, or OD servo piston (2) and
ATF could jump out. Carefully blow air little by little while
protecting with lint-free cloth A.
5.
Remove D-ring (1) from OD servo piston (2).
6.
Remove O-rings (1), (2) and (3) from OD servo piston retainer
(4).
(1): O-ring (small diameter)
(2): O-ring (medium diameter)
(3): O-ring (large diameter)
SCIA7050E
SCIA7051E
SCIA7052E
SCIA7053E
SCIA6492J
TM-582
< DISASSEMBLY AND ASSEMBLY >
[TYPE 2 (4AT: RE4F03B)]
REPAIR FOR COMPONENT PARTS
7.
Press in band servo piston assembly to remove from servo pis-
ton retainer.
8.
Place band servo piston stem on a wooden block, and remove
E-ring from band servo piston stem using suitable tool while
pressing spring retainer downward.
9.
Remove spring retainer (1), OD servo return spring (2), band
servo piston (3) and band servo thrust washer (4) from band
servo piston stem (5).
10. Remove O-rings from servo piston retainer.
11. Remove D-rings from band servo piston.
SAT293D
SCIA4336E
SCIA7054E
SCIA3671E
SCIA3688E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст