Nissan Sentra. Instruction — part 259
DLK-152
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
HOOD
3. Adjust the surface height of the hood assembly to front bumper
fascia and front fender according to the specified values by
rotating the hood bumper rubbers.
NOTE:
Only one hood bumper rubber shown for clarity.
4. Temporarily tighten the hood lock assembly bolts.
5. Adjust (A) and (B) as shown to the following value with hood's own weight by dropping it from approxi-
mately 200 mm (7.9 in) height or by pressing hood lightly [approximately 29 Nm (3.0 kg-m, 21 ft-lb)].
6. After adjustment, tighten hood hinge nuts and bolts to the specified torque. Refer to
CAUTION:
• Check hood hinge rotating part for poor lubrication. If necessary, apply a suitable multi-purpose
grease.
• After adjusting, apply touch-up paint (body color) to the head of hood hinge bolts and nuts.
7. Tighten the hood lock assembly bolts to specified torque.
8. Install the radiator core support upper cover.
9. If the clearance measurements between the hood and fender cannot be corrected by adjusting the hood,
the fender must be adjusted. Refer to
HOOD HINGE
HOOD HINGE : Removal and Installation
INFOID:0000000009756467
REMOVAL
1. Remove the fender protector. Refer to
EXT-28, "FENDER PROTECTOR : Removal and Installation -
.
2. Remove the core support upper cover. Refer to
3. Remove the front fascia. Refer to
EXT-17, "Removal and Installation"
4. Remove the front combination lamp. Refer to
EXL-119, "Removal and Installation"
.
5. Remove the front fender. Refer to
DLK-159, "Removal and Installation"
ALKIA0023GB
1.
Hood striker
2.
Primary latch
3.
Secondary striker
4.
Secondary latch
A. 21
± 1 mm (0.8 ± 0.04 in)
B. 6.8 mm (0.27 in)
PIIB5794E
HOOD
DLK-153
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
6. Remove hood hinge bolts (A) and hood hinge (1).
INSTALLATION
Installation is in the reverse order of removal.
Tighten bolts to specified torque. Refer to
DLK-149, "HOOD ASSEMBLY : Exploded View"
.
CAUTION:
• Before installing the hood hinge, apply anticorrosive agent onto the surface of the vehicle.
• After installation, perform hood assembly adjustment procedure. Refer to
HOOD SUPPORT ROD
HOOD SUPPORT ROD : Removal and Installation
INFOID:0000000009756468
REMOVAL
1. Support hood assembly using a suitable tool.
WARNING:
Bodily injury may occur if hood assembly is not supported properly when removing hood support
rod.
2. Rotate and remove hood support rod from grommet.
3. Remove grommet from hood hinge using a suitable tool, if necessary.
INSTALLATION
Installation is in the reverse order of removal.
HOOD LOCK CONTROL
ALKIA2891ZZ
DLK-154
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
HOOD
HOOD LOCK CONTROL : Exploded View
INFOID:0000000009756469
HOOD LOCK CONTROL : Removal and Installation
INFOID:0000000009756470
REMOVAL
1. Remove the fender protector (LH). Refer to
EXT-28, "FENDER PROTECTOR : Removal and Installation -
.
2. Remove the radiator core support upper cover clips (A) and
bolts (B) and remove.
1.
Hood lock assembly
2.
Hood lock release cable
3.
Hood lock/fuel filler door release handle assembly
A.
Hood lock release cable clip
Clip
AWKIA2088ZZ
AWKIA2156ZZ
HOOD
DLK-155
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
3. Remove the hood lock assembly bolts (A).
4. Disconnect the hood lock release cable from the hood lock assembly.
5. Remove the bolts (A), then separate the hood lock/fuel filler door
release handle assembly (1) from the hood lock release cable
(3) and fuel filler door release cable (2).
6. Remove the grommet from the dash assembly and pull the hood lock release cable into the passenger
compartment.
CAUTION:
While pulling, be careful not to damage (peel) the outside of the hood lock release cable.
INSTALLATION
1. Pull the hood lock release cable through the dash assembly into the engine compartment.
CAUTION:
Be careful not to bend the cable too much, keep the radius 100 mm (3.94 in) or more.
2. Attach the hood lock release cable (3) and the fuel filler door
release cable (2) to the hood lock/fuel filler door release handle
assembly (1).
3. Place hood lock/fuel filler door release handle assembly in posi-
tion and retain with bolts (A).
4. Check that the cable is not offset from the center of the grommet
and seat the grommet into the dash hole.
NOTE:
Make sure that the marked area (A) of the cable is located as
shown after mounting grommet to dash upper assembly.
Apply sealant around the grommet at * mark.
5. Position the hood lock release cable and clip it into place.
ALKIA2892ZZ
ALKIA2893ZZ
ALKIA2893ZZ
ALKIA2139ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст