Nissan Sentra. Instruction — part 258
DLK-148
< SYMPTOM DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
SQUEAK AND RATTLE TROUBLE DIAGNOSES
LAIA0071E
HOOD
DLK-149
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
REMOVAL AND INSTALLATION
HOOD
HOOD ASSEMBLY
HOOD ASSEMBLY : Exploded View
INFOID:0000000009756464
HOOD ASSEMBLY : Removal and Installation
INFOID:0000000009756465
CAUTION:
• Use two people when removing or installing hood assembly due to its heavy weight.
• Use protective tape or shop cloths to protect surrounding components from damage during removal
and installation of hood assembly.
REMOVAL
1. Support the hood assembly using a suitable tool.
WARNING:
Bodily injury may occur if hood assembly is not supported properly when removing hood assem-
bly.
2. Disconnect front washer nozzle and tube.
1.
Hood hinge (LH/RH)
2.
Hood assembly
3.
Hood bumper rubber
4.
Hood seal
5.
Hood insulator
6.
Hood support rod
7.
Hood support rod clamp
A.
Clip
AWKIA2152ZZ
DLK-150
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
HOOD
3. Remove hood hinge to hood nuts (A) and then remove the hood
assembly (1).
INSTALLATION
Installation is in the reverse order of removal.
Tighten hood hinge to hood nuts to specified torque. Refer to
DLK-149, "HOOD ASSEMBLY : Exploded View"
.
CAUTION:
• Before installing the hood hinge, apply anticorrosive agent onto the surface of the vehicle.
• After installation, perform the hood assembly adjustment procedure. Refer to
.
HOOD ASSEMBLY : Adjustment
INFOID:0000000009756466
Check the clearance and the surface height between hood and each part by visual inspection and tactile feel.
If the clearance and the surface height are out of specification, adjust them according to the adjustment proce-
dures.
AWKIA2157ZZ
1.
Hood assembly
2.
Front grille
3. Front combination lamp
4.
Front fender
5.
Hood lock assembly
AWKIA2154ZZ
HOOD
DLK-151
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Unit: mm (in)
CLEARANCE ADJUSTMENT
1. Loosen hood hinge (LH/RH) nuts and bolts.
NOTE:
The anticorrosive agent applied between the hoodledge and the hood hinges also acts as an adhesive.
This seal must be broken before the hinges will move.
2. Remove the radiator core support upper cover clips (A) and
bolts (B) and remove.
3. Loosen the hood lock assembly bolts.
4. Adjust the hood assembly so the clearance measurements are within specifications provided. Then
tighten the hood hinge nuts and bolts to specified torque. Refer to
.
5. Tighten the hood lock assembly bolts to specified torque. Refer to
.
6. Install the radiator core support upper cover.
HEIGHT ADJUSTMENT
1. Remove the radiator core support upper cover clips (A) and
bolts (B) and remove.
2. Loosen the hood lock assembly bolts.
Section
Item
Measurement
Standard
Parallelism
Equality
A – A
D
Clearance
6.2
±2.2 (0.24 ±0.09)
2.0
—
E
Surface height
—
—
—
B – B
F
Clearance
3.5
±2.0 (0.14 ±0.08)
2.0
3.0
G
Surface height
3.6
±2.0 (0.14 ±0.08)
2.0
2.0
C – C
H
Clearance
3.7
±1.0 (0.15 ±0.04)
2.0
2.0
J
Surface height
0.0
±1.0 (0.00 ±0.04)
—
—
AWKIA2156ZZ
AWKIA2156ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст