Nissan Sentra. Instruction — part 901
TM-240
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F11A]
SHIFT POSITION INDICATOR CIRCUIT
SHIFT POSITION INDICATOR CIRCUIT
Component Parts Function Inspection
INFOID:0000000009759488
1.
CHECK SHIFT POSITION INDICATOR
1. Start the engine.
2. Shift selector lever.
3. Check that the selector lever position and the shift position indicator on the combination meter are identi-
cal.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Go to
Diagnosis Procedure
INFOID:0000000009759489
1.
CHECK TCM INPUT/OUTPUT SIGNAL
With CONSULT
1. Start the engine.
2. Select “Data Monitor” in “TRANSMISSION”.
3. Select “RANGE”.
4. Shift selector lever.
5. Check that selector lever position, “RANGE” on the CONSULT screen, and shift position indicator display
on the combination meter are identical.
Is the check result normal?
YES
>> INSPECTION END
NO-1 (“RANGE” is changed but is not displayed on the shift position indicator.>>Check “Self Diagnostic
Result” in “TRANSMISSION”.
NO-2 (“RANGE” and shift position indicator are different.)>>Check “Self Diagnostic Result” in “TRANSMIS-
SION”.
NO-3 (Specific“RANGE” is not displayed on the shift position indicator.)>>Check “Self Diagnostic Result” in
“METER/M&A”.
SHIFT LOCK SYSTEM
TM-241
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F11A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
SHIFT LOCK SYSTEM
Component Function Check
INFOID:0000000009759490
1.
CHECK SHIFT LOCK OPERATION (PART 1)
1. Turn ignition switch ON.
2. Shift the selector lever to park “P” position.
3. Attempt to shift the selector lever to any other position with the brake pedal released.
Can the selector lever be shifted to any other position?
YES
>> Go to
NO
>> GO TO 2.
2.
CHECK SHIFT LOCK OPERATION (PART 2)
Attempt to shift the selector lever to any other position with the brake pedal depressed.
Can the selector lever be shifted to any other position?
YES
>> Inspection End.
NO
>> Go to
Diagnosis Procedure
INFOID:0000000009759491
Regarding Wiring Diagram information, refer to
.
1.
CHECK POWER SOURCE (PART 1)
1. Turn ignition switch OFF.
2. Disconnect stop lamp switch connector.
3. Turn ignition switch ON.
4. Check the voltage between the stop lamp switch harness connector terminal and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> GO TO 9.
2.
CHECK STOP LAMP SWITCH MOUNTING POSITION
Check stop lamp switch mounting position. Refer to
.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Adjust stop lamp switch mounting position.
3.
CHECK STOP LAMP SWITCH
Check stop lamp switch. Refer to
TM-243, "Component Inspection (Stop Lamp Switch)"
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace stop lamp switch.
4.
CHECK CIRCUIT BETWEEN STOP LAMP SWITCH AND CVT SHIFT SELECTOR (PART 1)
1. Disconnect CVT shift selector connector.
2. Check the continuity between the stop lamp switch harness connector terminal and the CVT shift selector
harness connector terminal.
+
–
Voltage
Stop lamp switch
Connector
Terminal
E60
3
Ground
Battery voltage
TM-242
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F11A]
SHIFT LOCK SYSTEM
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace damaged parts.
5.
CHECK CIRCUIT BETWEEN STOP LAMP SWITCH AND CVT SHIFT SELECTOR (PART 2)
Check the continuity between the stop lamp switch harness connector terminal and ground.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair or replace damaged parts.
6.
CHECK GROUND CIRCUIT
Check the continuity between the CVT shift selector harness connector terminal and ground.
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> Repair or replace damaged parts.
7.
CHECK PART POSITION SWITCH
1. Disconnect park position switch connector.
2. Check park position switch. Refer to
TM-243, "Component Inspection (Park Position Switch)"
Is the inspection result normal?
YES
>> GO TO 8.
NO
>> Repair or replace damaged parts.
8.
CHECK SHIFT LOCK SOLENOID
1. Disconnect shift lock solenoid connector.
2. Check shift lock solenoid. Refer to
TM-243, "Component Inspection (Shift Lock Solenoid)"
Is the inspection result normal?
YES
>> GO TO 9.
NO
>> Repair or replace damaged parts.
9.
DETECT MALFUNCTIONING ITEM
Check the following items:
• Open or short circuit of the harness between ignition switch and stop lamp switch connector. Refer to
"Wiring Diagram — Ignition Power Supply —"
• Ignition switch
• 10A fuse [No.5, fuse block (J/B)]. Refer to
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-39, "Intermittent Incident"
.
NO
>> Repair or replace damaged parts.
Stop lamp switch
CVT shift selector
Continuity
Connector
Terminal
Connector
Terminal
E60
4
M38
3
Yes
Stop lamp switch
—
Continuity
Connector
Terminal
E60
4
Ground
No
CVT shift selector
—
Continuity
Connector
Terminal
M38
4
Ground
Yes
SHIFT LOCK SYSTEM
TM-243
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F11A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
Component Inspection (Shift Lock Solenoid)
INFOID:0000000009759492
1.
CHECK SHIFT LOCK SOLENOID
Apply voltage to terminals of shift lock solenoid and park position switch (shift selector) connector and check
that shift lock solenoid is activated.
CAUTION:
• Connect a fuse between the terminals when applying voltage.
• Never cause shorting between terminals.
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Replace CVT shift selector. Refer to
TM-253, "Removal and Installation"
Component Inspection (Park Position Switch)
INFOID:0000000009759493
1.
CHECK PARK POSITION SWITCH (SHIFT SELECTOR)
Apply voltage to terminals of shift lock solenoid and park position switch (shift selector) connector and check
that shift lock solenoid is activated.
CAUTION:
• Connect a fuse between the terminals when applying voltage.
• Never cause shorting between terminals.
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Replace CVT shift selector. Refer to
TM-253, "Removal and Installation"
Component Inspection (Stop Lamp Switch)
INFOID:0000000009759494
1.
CHECK STOP LAMP SWITCH
Check the continuity between the stop lamp switch connector terminals.
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Replace stop lamp switch. Refer to
.
+ (fuse)
-
Condition
Status
Shift lock solenoid
Terminal
3
4
Apply 12 V between termi-
nals 3 and 4 with the park
position switch (shift selec-
tor) in the "P" (park) posi-
tion.
Shift lock solenoid operates
+ (fuse)
-
Condition
Status
Shift lock solenoid
Terminal
3
4
Apply 12 V between termi-
nals 3 and 4 with the park
position switch (shift selec-
tor) in the "P" (park) posi-
tion.
Shift lock solenoid operates
Stop lamp switch
Condition
Continuity
Terminal
3 – 4
Depressed brake pedal
Yes
Released brake pedal
No
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст