Nissan Sentra. Instruction — part 907
TM-264
< REMOVAL AND INSTALLATION >
[CVT: RE0F11A]
AIR BREATHER HOSE
AIR BREATHER HOSE
Exploded View
INFOID:0000000009759511
Removal and Installation
INFOID:0000000009759512
REMOVAL
1. Remove clips from harness bracket.
2. Remove air breather hose from transaxle assembly.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not bend the air breather hose to prevent damage to the hose.
• Do not reuse clips.
• Securely install the clips to the harness bracket.
• Be sure to insert it fully until its end reaches the stop when
inserting air breather hose (1) to transaxle tube (A).
• Install air breather hose to transaxle tube so that the paint
mark (B) is facing frontward.
Harness bracket
.
Clip
.
Air breather hose
: Vehicle front
: Always replace after every disassembly.
JSDIA3584ZZ
JSDIA1887ZZ
G SENSOR
TM-265
< REMOVAL AND INSTALLATION >
[CVT: RE0F11A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
G SENSOR
Exploded View
INFOID:0000000009759513
Removal and Installation
INFOID:0000000009759514
WARNING:
Do not leave any objects (screwdrivers, tools, etc.) on the seat during seat repair. It can lead to per-
sonal injury if the side air bag module should accidentally deploy.
CAUTION:
• Do not drop or strike G sensor, because it has little tolerance for impact.
• Do not use a power tool and avoid impact.
REMOVAL
1. Disconnect the negative and positive battery terminals and wait at least three minutes. Refer to
"Removal and Installation (Battery)"
.
2. Remove driver seat. Refer to
SE-18, "DRIVER SIDE : Removal and Installation - Seat Assembly"
.
3. Remove center pillar lower garnish (left side) and dash side finisher (left side). Refer to
PILLAR LOWER FINISHER : Removal and Installation"
(center pillar lower garnish) and
SIDE FINISHER : Removal and Installation"
(dash side finisher).
4. Pull up floor carpet. Refer to
INT-35, "Removal and Installation"
.
5. Disconnect G sensor harness connector.
6. Remove G sensor.
7. Remove bracket.
INSTALLATION
Installation is the reverse order of removal.
Adjustment
INFOID:0000000009759515
ADJUSTMENT AFTER INSTALLATION
Perform “CALIBRATION OF G SENSOR”. Refer to
.
G sensor
Bracket
: Vehicle front
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)
JSDIA3672GB
TM-266
< REMOVAL AND INSTALLATION >
[CVT: RE0F11A]
OIL PAN
OIL PAN
Exploded View
INFOID:0000000009759516
Removal and Installation
INFOID:0000000009759517
REMOVAL
1. Remove the engine under cover. Refer to
EXT-31, "ENGINE UNDER COVER : Removal and Installation"
.
2. Remove the drain plug and overflow tube, and then drain the CVT fluid.
CAUTION:
When draining CVT fluid use safety glasses.
3. Remove the drain plug gasket from the drain plug.
Transaxle assembly
Oil pan gasket
Magnet
Oil pan
Overflow tube
Drain plug gasket
Drain plug
Oil pan fitting bolt
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
: N·m (kg-m, it-lb)
JSDIA1879GB
OIL PAN
TM-267
< REMOVAL AND INSTALLATION >
[CVT: RE0F11A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
4. Remove the oil pan bolts (
), and then remove the oil pan and
oil pan gasket.
5. Remove the magnets from the oil pan.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not reuse oil pan gasket and drain plug gasket.
• When installing the oil pan bolts, be sure to use new bolts.
• Completely remove all moisture, oil and old gasket, etc. from the oil pan gasket surface of transaxle
case and oil pan.
• When installing the overflow tube, be sure to tighten to the specified torque. If it is not tightened to
the specified torque, the tube may be damaged.
• When the oil pan is installed, tighten bolts in the order shown in the
figure after temporarily tightening the oil pan bolt.
Inspection
INFOID:0000000009759518
INSPECTION AFTER REMOVAL
Check oil pan for foreign material.
• If a large amount of worn material is found, clutch plate may be worn.
• If iron powder is found, bearings, gears, or clutch plates may be worn.
• If aluminum powder is found, bushing may be worn, or chips or burrs of aluminum casting parts may enter.
Check points where wear is found in all cases.
INSPECTION AFTER INSTALLATION
Start the engine and check visually that there is no leakage of CVT fluid.
: Front
JSDIA1874ZZ
: Front
JSDIA1884ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст