Nissan Sentra. Instruction — part 480
DOOR MIRROR TURN SIGNAL LAMP
EXL-123
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
DOOR MIRROR TURN SIGNAL LAMP
Removal and Installation
INFOID:0000000009757548
The door mirror side turn signal lamp is integrated into the door mirror assembly and is serviced as an assem-
EXL-124
< REMOVAL AND INSTALLATION >
HIGH-MOUNTED STOP LAMP
HIGH-MOUNTED STOP LAMP
Removal and Installation
INFOID:0000000009757549
HIGH-MOUNTED STOP LAMP - WITH REAR SPOILER
Removal
1. Remove the rear air spoiler. Refer to
EXT-46, "Removal and Installation"
.
2. Remove the screws and the high-mount stop lamp from the rear air spoiler.
Installation
Installation is in the reverse order of removal.
HIGH-MOUNTED STOP LAMP - WITHOUT REAR SPOILER
Removal
1. Slide high-mounted stop lamp (1) rearward on parcel shelf to
provide clearance for front tabs (A).
2. Lift front of lamp assembly up and pull forward to provide clear-
ance for rear tabs (B).
3. Disconnect the harness connector from the high-mounted stop lamp and remove.
Installation
Installation is in the reverse order of removal.
Bulb Replacement
INFOID:0000000009757550
HIGH-MOUNTED STOP LAMP - WITH REAR SPOILER
The high-mounted stop lamp LED bulb is integrated into the high-mounted stop lamp and is serviced as an
assembly. Refer to
EXL-124, "Removal and Installation"
.
HIGH-MOUNTED STOP LAMP - WITHOUT REAR SPOILER
The high-mounted stop lamp LED bulb is integrated into the high-mounted stop lamp and is serviced as an
assembly. Refer to
EXL-124, "Removal and Installation"
.
ALLIA1135ZZ
LICENSE PLATE LAMP
EXL-125
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
LICENSE PLATE LAMP
Removal and Installation
INFOID:0000000009757551
REMOVAL
1. Remove the license lamp finisher. Refer to
EXT-44, "Removal and Installation"
.
2. Disconnect the harness connector (A) from the license plate
lamp (1).
3. Release pawl and remove.
: Pawl
INSTALLATION
Installation is in the reverse order of removal.
Bulb Replacement
INFOID:0000000009757552
WARNING:
Do not touch bulb while it is lit or right after being turned off. Burning may result.
CAUTION:
• Do not touch glass surface of the bulb with bare hands or allow oil or grease to get on it to prevent
damage to bulb.
• Do not leave the bulb out of the lamp reflector for a long time because dust, moisture, smoke, etc.
may affect the performance of the lamp.
REMOVAL
1. Position trunk lid finisher aside. Refer to
INT-45, "Removal and Installation"
2. Rotate license plate lamp bulb socket (2) counterclockwise and
remove from license plate lamp (1).
3. Remove license plate lamp bulb (A) from license plate lamp bulb
socket (2).
INSTALLATION
Installation is in the reverse order of removal.
ALLIA1134ZZ
ALLIA1133ZZ
EXL-126
< REMOVAL AND INSTALLATION >
REAR COMBINATION LAMP
REAR COMBINATION LAMP
Exploded View
INFOID:0000000009757553
Removal and Installation
INFOID:0000000009757554
Removal
1. Partially remove trunk side finisher. Refer to
INT-43, "TRUNK SIDE FINISHER : Removal and Installa-
2. Remove the rear combination lamp nuts (B).
3. Disconnect the harness connector (A) from the rear combination
lamp.
4. Pull the rear combination lamp rearward and remove.
1.
Rear combination lamp
2. Rear turn signal lamp bulb
3. Rear turn signal lamp socket
4.
LED lamp harness connector
5. Rear combination lamp harness
connector
6. Back-up lamp bulb socket
7.
Back-up lamp bulb
ALLIA1210ZZ
ALLIA1211ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст