Nissan Sentra. Instruction — part 481
REAR COMBINATION LAMP
EXL-127
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
Installation
Installation is the reverse order of removal.
Bulb Replacement
INFOID:0000000009757555
WARNING:
Do not touch bulb while it is lit or right after being turned off. Burning may result.
CAUTION:
• Do not touch glass surface of the bulb with bare hands or allow oil or grease to get on it to prevent
damage to bulb.
• Do not leave the bulb out of the lamp reflector for a long time because dust, moisture, smoke, etc.
may affect the performance of the lamp.
REAR TURN SIGNAL LAMP BULB
Removal
1. Remove the rear combination lamp. Refer to
EXL-126, "Removal and Installation"
2. Rotate the rear turn signal lamp bulb socket counterclockwise and remove.
3. Remove the rear turn signal lamp bulb from bulb socket.
Installation
Installation is in the reverse order of removal.
CAUTION:
After installing, be sure to install the bulb socket securely to ensure watertightness.
STOP/TAIL LAMP
The stop/tail lamp is integrated into the rear combination lamp and is serviced as an assembly. Refer to
126, "Removal and Installation"
BACK-UP LAMP BULB
Removal
1. Remove the rear combination lamp. Refer to
EXL-126, "Removal and Installation"
2. Rotate the back-up lamp bulb socket counterclockwise and remove.
3. Remove the back-up lamp bulb from bulb socket.
Installation
Installation is in the reverse order of removal.
CAUTION:
After installing, be sure to install the bulb socket securely to ensure watertightness.
EXL-128
< REMOVAL AND INSTALLATION >
COMBINATION SWITCH
COMBINATION SWITCH
Exploded View
INFOID:0000000009757556
NOTE:
Shown with the steering wheel removed for clarity only.
Removal and Installation
INFOID:0000000009757557
REMOVAL
CAUTION:
• Before servicing, turn the ignition switch OFF, disconnect both battery terminals and wait at least
three minutes.
• Do not use air or electric tools when removing or installing the combination switch.
1. Disconnect both the negative and positive battery terminals, then wait at least three minutes. Refer to
50, "Removal and Installation (Battery)"
2. Remove the steering column covers. Refer to
IP-16, "Removal and Installation"
.
3. Rotate steering wheel clockwise to access first combination switch bolt and remove.
4. Rotate steering wheel counter-clockwise to access second combination switch bolt and remove.
5. Disconnect the harness connector from the combination switch and remove.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• After the work is completed, make sure no system malfunction is detected by air bag warning lamp.
• In case a malfunction is detected by the air bag warning lamp, reset with the self-diagnosis function
and delete the memory with CONSULT.
• If a malfunction is still detected after the above operation, perform self-diagnosis to repair malfunc-
SRC-41, "ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair
.
AWMIA1293ZZ
1.
Combination switch
2.
Combination switch harness connector
Front
HAZARD SWITCH
EXL-129
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
HAZARD SWITCH
Removal and Installation
INFOID:0000000009757558
REMOVAL
1. Remove cluster lid C (1). Refer to
2. Release pawls at (
) and remove hazard switch (2).
INSTALLATION
Installation is in the reverse order of removal.
ALLIA1140ZZ
EXL-130
< REMOVAL AND INSTALLATION >
OPTICAL SENSOR
OPTICAL SENSOR
Removal and Installation
INFOID:0000000009757559
REMOVAL
1. Remove the defroster grille (LH) using a suitable tool.
2. Disconnect the harness connector from the optical sensor.
3. Release the pawls and remove the optical sensor.
INSTALLATION
Installation is in the reverse order of removal.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст