Nissan Sentra. Instruction — part 197
CHG-4
< PREPARATION >
PREPARATION
PREPARATION
PREPARATION
Special Service Tool
INFOID:0000000009755951
The actual shape of the tools may differ from those illustrated here.
Commercial Service Tool
INFOID:0000000009755952
Tool number
(TechMate No.)
Tool name
Description
—
(—) Model GR8-1200 NI
Multitasking battery and electrical di-
agnostic station
Tests batteries, starting and charging sys-
tems and charges batteries.
For operating instructions, refer to diagnostic
station instruction instruction.
—
(—) Model EXP-800 NI
Battery and electrical diagnostic ana-
lyzer
Tests batteries and charging systems.
For operating instructions, refer to diagnostic
analyzer instruction instruction.
AWIIA1239ZZ
JSMIA0806ZZ
Tool name
Description
Power tool
Loosening nuts, screws and bolts
PIIB1407E
CHG
COMPONENT PARTS
CHG-5
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
SYSTEM DESCRIPTION
COMPONENT PARTS
Component Parts Location
INFOID:0000000009755953
AWMIA1322GB
1.
Generator
2.
IPDM E/R (view with air inlet duct re-
moved)
3.
ECM
4.
Battery current sensor
5.
Charge warning lamp indicator
CHG-6
< SYSTEM DESCRIPTION >
COMPONENT PARTS
Component Description
INFOID:0000000009755954
Component part
Description
Generator (IC regulator)
The IC regulator controls the power generation voltage by the tar-
get power generation voltage based on the received PWM com-
mand signal.
When there is no PWM command signal, the generator performs
the normal power generation according to the characteristic of the
IC regulator.
IPDM E/R
The IPDM E/R converts the received power generation command
value into a pulse width modulated (PWM) command signal and
sends it to the IC regulator.
ECM
The battery current sensor detects the charging/discharging cur-
rent of the battery. The ECM judges the battery condition based on
this signal.
The ECM judges whether to request more output via the power
generation voltage variable control according to the battery condi-
tion.
When performing the power generation voltage variable control,
the ECM calculates the target power generation voltage according
to the battery condition and sends the calculated value as the pow-
er generation command value to the IPDM E/R.
Battery current sensor
The battery current sensor is located on the negative battery cable
terminal. The battery current sensor detects the charging/dis-
charging current of the battery and sends a voltage signal to the
ECM according to the current value detected.
Combination meter (charge warning lamp)
The IC regulator warning function activates to illuminate the
charge warning lamp if any of the following symptoms occur while
generator is operating:
·Excessive voltage is produced.
·No voltage is produced.
CHG
CHARGING SYSTEM
CHG-7
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
CHARGING SYSTEM
System Diagram
INFOID:0000000009755955
System Description
INFOID:0000000009755956
The generator provides DC voltage to operate the vehicle's electrical system and to keep the battery charged.
The voltage output is controlled by the IC regulator.
Component Description
INFOID:0000000009755957
AWMIA1334GB
Component part
Description
Generator
Terminal “1”
Refer to
.
Terminal “2”
Refer to
.
Terminal “3”
Refer to
.
Terminal “4”
Used for the power generation voltage variable control system.
Refer to
Combination meter (Charge warning lamp)
The IC regulator warning function activates to illuminate the
charge warning lamp if any of the following symptoms occur while
generator is operating:
• Excessive voltage is produced.
• No voltage is produced.
IPDM E/R
Used for the power generation voltage variable control system.
Refer to
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст