Nissan Quest E52. Instruction — part 669
FAX-4
< PREPARATION >
PREPARATION
PREPARATION
PREPARATION
Special Service Tool
INFOID:0000000009651659
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Tool number
(Kent-Moore No.)
Tool name
Description
KV40104000
(
—
)
Hub lock nut wrench
a: 85 mm (3.35 in)
b: 65 mm (2.56 in)
Removing and Installing wheel hub lock nut.
KV40107300
(
—
)
Boot band crimping tool
Installing boot band
KV40107500
(
—
)
Drive shaft attachment
Removing drive shaft
KV38107900
(
—
)
Protector
a: 32 mm (1.26 in) dia.
Installing drive shaft
ST35271000
(J-26091)
Drift
a: 72 mm (2.83 in) dia.
b: 63 mm (2.48 in) dia.
Installing support bearing
ST17130000
(
—
)
Drift
a: 32 mm (1.26 in) dia.
b: 60 mm (2.36 in) dia.
Removing support bearing
ZZA0802D
ZZA1229D
ZZA1230D
PDIA1183J
ZZA0837D
ZZA0836D
PREPARATION
FAX-5
< PREPARATION >
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
Commercial Service Tools
INFOID:0000000009651660
Tool name
Description
Drive shaft puller
Removing drive shaft joint sub assembly
Sliding hammer
Removing drive shaft
Ball joint remover
Removing hub bolt
Power tool
Loosening bolts and nuts
JPDIG0152ZZ
ZZA0023D
NT146
PBIC0190E
FAX-6
< SYMPTOM DIAGNOSIS >
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
SYMPTOM DIAGNOSIS
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
NVH Troubleshooting Chart
INFOID:0000000009651661
Use chart below to find the cause of the symptom. If necessary, repair or replace these parts.
×
: Applicable
Reference
—
—
—
NVH in
F
AX
and FS
U sections
Re
fe
r to
FRO
N
T A
X
L
E in
th
is
ch
art
NVH in WT
section
NVH in WT
section
Refe
r to
DRIVE
SHAFT i
n
t
h
is
cha
rt
NVH in BR
section
NVH in ST
section
Possible cause and SUSPECTED PARTS
Exc
e
ss
iv
e j
o
in
t a
n
g
le
Jo
in
t s
lid
in
g re
si
stan
ce
Im
ba
lan
c
e
Im
pro
per in
st
a
lla
ti
on
,
lo
os
en
es
s
Part
s int
e
rference
Whe
e
l be
ari
n
g
da
m
age
FRONT AXLE AND F
R
ONT
SUSPENSI
ON
FRONT AXL
E
TIRE
ROA
D
WHEEL
DRIVE SHA
F
T
BRAKE
STEERI
N
G
Symptom
DRIVE
SHAFT
Noise
×
×
×
×
×
×
×
×
×
Shake
×
×
×
×
×
×
×
×
×
FRONT
AXLE
Noise
×
×
×
×
×
×
×
×
×
Shake
×
×
×
×
×
×
×
×
×
Vibration
×
×
×
×
×
×
×
Shimmy
×
×
×
×
×
×
×
Judder
×
×
×
×
×
×
Poor quality ride or handling
×
×
×
×
×
FRONT WHEEL HUB AND KNUCKLE
FAX-7
< PERIODIC MAINTENANCE >
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
PERIODIC MAINTENANCE
FRONT WHEEL HUB AND KNUCKLE
Inspection
INFOID:0000000009651662
COMPONENT PART
Check that the mounting conditions (looseness, backlash) of each component and component conditions
(wear, damage) are normal.
WHEEL HUB ASSEMBLY (BEARING-INTEGRATED TYPE)
Check the following items, and replace the part if necessary.
• Move wheel hub assembly in the axial direction by hand. Check there is no looseness of wheel bearing.
• Rotate wheel hub assembly and check there is no unusual noise or other irregular conditions. If there is any
of irregular conditions, replace wheel hub assembly.
Axial end play
: Refer to
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст