Nissan Quest E52. Instruction — part 629
EXL-120
< SERVICE DATA AND SPECIFICATIONS (SDS)
[XENON TYPE]
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Bulb Specifications
INFOID:0000000009653115
Item
Type
Wattage (W)
Front combination lamp
Headlamp (HI)
HB3 (Halogen)
60
Headlamp (LO)
D2S (Xenon)
35
Front turn signal lamp/
Parking lamp
S25 (Amber)
27/8
Front side marker lamp
W5W
5
Front fog lamp
H8
35
Side turn signal lamp (integrated into the door mirror)
LED
—
Rear combination lamp
Stop lamp/
Tail lamp (side marker)
W21/5W
21/5
Rear turn signal lamp
WY21W (Amber)
21
Back-up lamp
W16W
16
License plate lamp
W5W
5
High-mounted stop lamp
LED
—
PRECAUTIONS
EXL-121
< PRECAUTION >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000009653116
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this
Instruction.
WARNING:
Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see “SRS AIR BAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Instruction. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Precautions for Removing Battery Terminal
INFOID:0000000009980279
• When removing the 12V battery terminal, turn OFF the ignition
switch and wait at least 30 seconds.
NOTE:
ECU may be active for several tens of seconds after the ignition
switch is turned OFF. If the battery terminal is removed before ECU
stops, then a DTC detection error or ECU data corruption may
occur.
• For vehicles with the 2-batteries, be sure to connect the main bat-
tery and the sub battery before turning ON the ignition switch.
NOTE:
If the ignition switch is turned ON with any one of the terminals of
main battery and sub battery disconnected, then DTC may be
detected.
• After installing the 12V battery, always check "Self Diagnosis Result" of all ECUs and erase DTC.
NOTE:
The removal of 12V battery may cause a DTC detection error.
SEF289H
EXL-122
< SYSTEM DESCRIPTION >
[HALOGEN TYPE]
COMPONENT PARTS
SYSTEM DESCRIPTION
COMPONENT PARTS
Component Parts Location
INFOID:0000000009653117
No.
Part
Function
1.
Optical sensor
2.
BCM
• Detects each switch condition by the combination switch reading function
• Judges that the exterior lamps are turned ON according to the vehicle condition
• Requests the headlamp relay (High/Low), tail lamp relay and front fog lamp relay
ON to IPDM E/R (via CAN communication)
• Requests the high beam indicator lamp and tail lamp indicator lamp ON to the
combination meter (via CAN communication)
• Judges the outside brightness from the optical sensor signal.
• Judges the ON/OFF timing according to the vehicle condition.
• Judges the ON/OFF status of the exterior lamp according to the outside bright-
ness and the vehicle condition.
• Refer to
BCS-4, "BODY CONTROL SYSTEM : Component Parts Location"
for
detailed installation location.
3.
Daytime running light relay
*
EXL-123, "Daytime Running Light Relay"
.
4.
IPDM E/R
• Controls the integrated relay, and supplies voltage to the load according to the re-
quest from BCM (via CAN communication).
PCS-4, "IPDM E/R : Component Parts Location"
for detailed installation
location.
5.
Front turn signal lamp/Parking lamp
Refer to
EXL-123, "Bulb Specifications"
.
6.
Headlamp HI
Refer to
EXL-123, "Bulb Specifications"
.
7.
Front fog lamp
EXL-123, "Bulb Specifications"
.
8.
Headlamp LO
EXL-123, "Bulb Specifications"
.
9.
Front side marker lamp
Refer to
EXL-123, "Bulb Specifications"
.
JMLIA2103ZZ
COMPONENT PARTS
EXL-123
< SYSTEM DESCRIPTION >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
*
: With daytime running light system
Optical Sensor
INFOID:0000000009653118
Optical sensor converts the outside brightness (lux) to voltage and transmits the optical sensor signal to BCM.
Daytime Running Light Relay
INFOID:0000000009653119
Headlamp HI ground circuit is switched according to request from IPDM E/R.
Hazard Switch
INFOID:0000000009653120
Inputs the hazard switch ON/OFF signal to BCM.
Bulb Specifications
INFOID:0000000009653121
10.
Air bag diagnosis sensor unit
Transmits air bag signal to BCM.
Refer to
SRC-8, "Component Parts Location"
for detailed installation location.
11.
Side turn signal lamp
Refer to
EXL-123, "Bulb Specifications"
.
12.
Hazard switch
Refer to
.
13.
Push-button ignition switch
Refer to
DLK-18, "DOOR LOCK SYSTEM : Component Parts Location"
14.
Combination meter
• Blinks the turn signal indicator lamp and outputs the turn signal operating sound
with integrated buzzer according to the request from BCM (via CAN communica-
tion).
• Turns the high beam indicator lamp and tail lamp indicator lamp ON according to
the request from BCM (via CAN communication).
15.
Combination switch
(Lighting & turn signal switch)
Refer to
BCS-8, "COMBINATION SWITCH READING SYSTEM : System Descrip-
.
16.
Front door switch (driver side)
Refer to
DLK-18, "DOOR LOCK SYSTEM : Component Parts Location"
17.
Slide door switch (LH)
Refer to
DLK-18, "DOOR LOCK SYSTEM : Component Parts Location"
18.
Rear side marker lamp
Refer to
EXL-123, "Bulb Specifications"
.
19.
Rear turn signal lamp
Refer to
EXL-123, "Bulb Specifications"
.
20.
Tail lamp
Refer to
EXL-123, "Bulb Specifications"
.
21.
Back door switch
Refer to
DLK-18, "DOOR LOCK SYSTEM : Component Parts Location"
22.
License plate lamp
Refer to
EXL-123, "Bulb Specifications"
.
No.
Part
Function
Item
Type
Wattage (W)
Front combination lamp
Headlamp (HI)
HB3 (Halogen)
60
Headlamp (LO)
H11 (Halogen)
55
Front turn signal lamp/
Parking lamp
S25
27/8
Front side marker lamp.
W5W
5
Front fog lamp
H8
35
Side turn signal lamp (integrated into the door mirror)
LED
—
Rear combination lamp
Stop lamp/
Tail lamp (side marker lamp)
W21/5W
21/5
Rear turn signal lamp
WY21W (Amber)
21
Back-up lamp
W16W
16
License plate lamp
W5W
5
High-mounted stop lamp
LED
—
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст