Nissan Quest E52. Instruction — part 628
EXL-116
< REMOVAL AND INSTALLATION >
[XENON TYPE]
BACK-UP LAMP
1.
Remove touch sensor.(with automatic back door) Refer to
DLK-477, "TOUCH SENSOR : Removal and
.
2.
Remove back door lower finisher. Refer to
INT-48, "BACK DOOR LOWER FINISHER : Removal and
.
3.
Disconnect back-up lamp connector.
4.
Remove back-up lamp mounting nuts, and then remove back-up lamp.
5.
Remove seal packing
INSTALLATION
Note the following item, and then install in the reverse order of removal.
CAUTION:
Seal packing cannot be reused.
Replacement
INFOID:0000000009653107
CAUTION:
• Disconnect the battery negative terminal or the fuse.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
• Never touch bulb by hand while it is lit or right after being turned off.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
BACK-UP LAMP BULB
1.
Remove back door lower finisher. Refer to
INT-48, "BACK DOOR LOWER FINISHER : Removal and
.
2.
Rotate back-up lamp bulb socket counterclockwise, and then remove back-up lamp bulb socket.
3.
Remove back-up lamp bulb from back-up lamp bulb socket.
HIGH-MOUNTED STOP LAMP
EXL-117
< REMOVAL AND INSTALLATION >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
HIGH-MOUNTED STOP LAMP
Exploded View
INFOID:0000000009653108
Removal and Installation
INFOID:0000000009653109
REMOVAL
1.
Remove rear spoiler. Refer to
EXT-45, "Removal and Installation"
.
2.
Remove high-mounted stop lamp mounting nuts.
3.
Remove high-mounted stop lamp from rear spoiler.
INSTALLATION
Install in the reverse order of removal.
1.
Rear spoiler
2.
High-mounted stop lamp
JMLIA1564ZZ
EXL-118
< REMOVAL AND INSTALLATION >
[XENON TYPE]
LICENSE PLATE LAMP
LICENSE PLATE LAMP
Exploded View
INFOID:0000000009653110
Removal and Installation
INFOID:0000000009653111
CAUTION:
Disconnect the battery negative terminal or the fuse.
REMOVAL
1.
Remove back door lower finisher. Refer to
EXT-47, "Removal and Installation"
2.
Disconnect license plate lamp connector.
3.
Remove license plate lamp while pushing a resin clip, and then remove license plate lamp.
INSTALLATION
Install in the reverse order of removal.
Replacement
INFOID:0000000009653112
CAUTION:
• Disconnect the battery negative terminal or the fuse.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
• Never touch bulb by hand while it is lit or right after being turned off.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
LICENSE PLATE LAMP BULB
1.
Remove back door lower finisher. Refer to
EXT-47, "Removal and Installation"
2.
Disconnect license plate lamp connector.
3.
Rotate license plate lamp bulb socket counterclockwise and unlock it.
4.
Remove license plate lamp bulb from license plate lamp bulb socket.
1.
License plate lamp bulb socket
2.
License plate lamp bulb
3.
License plate lamp housing
4.
Back door finisher
: Clip
: Pawl
JMLIA2205ZZ
REFLEX REFLECTOR
EXL-119
< REMOVAL AND INSTALLATION >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
REFLEX REFLECTOR
Exploded View
INFOID:0000000009653113
Removal and Installation
INFOID:0000000009653114
REMOVAL
1.
Remove rear bumper fascia assembly. Refer to
EXT-16, "REAR BUMPER : Removal and Installation"
.
2.
Remove reflex reflector (1) fixing screws (A) (LH and RH), and
then remove reflex reflector (LH and RH).
INSTALLATION
Install in the reverse order of removal.
1.
Reflex reflector
: Pawl
JMLIA1567ZZ
JMKIA1974ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст