Nissan Quest E52. Instruction — part 518
EC-282
< DTC/CIRCUIT DIAGNOSIS >
[VQ35DE]
P0441 EVAP CONTROL SYSTEM
P0441 EVAP CONTROL SYSTEM
DTC Logic
INFOID:0000000009651122
DTC DETECTION LOGIC
NOTE:
If DTC P0441 is displayed with other DTC such as P2122, P2123, P2127, P2128 or P2138, first perform
trouble diagnosis for other DTC.
In this evaporative emission (EVAP) control system, purge flow occurs during non-closed throttle conditions.
Purge volume is related to air intake volume. Under normal purge conditions (non-closed throttle), the EVAP
canister purge volume control solenoid valve is open to admit purge flow. Purge flow exposes the EVAP con-
trol system pressure sensor to intake manifold vacuum.
Under normal conditions (non-closed throttle), sensor output voltage indicates if pressure drop and purge flow
are adequate. If not, a malfunction is determined.
DTC CONFIRMATION PROCEDURE
1.
INSPECTION START
Will CONSULT be used?
Will CONSULT be used?
YES
>> GO TO 2.
NO
>> GO TO 6.
2.
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following before conduct-
ing the next test.
1.
Turn ignition switch OFF and wait at least 10 seconds.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P0441
EVAP control system in-
correct purge flow
EVAP control system does not operate proper-
ly, EVAP control system has a leakage between
intake manifold and EVAP control system pres-
sure sensor.
• EVAP canister purge volume control so-
lenoid valve stuck closed
• EVAP control system pressure sensor
and the circuit
• Loose, disconnected or improper con-
nection of rubber tube
• Blocked rubber tube
• Cracked EVAP canister
• EVAP canister purge volume control so-
lenoid valve circuit
• Accelerator pedal position sensor
• Blocked purge port
• EVAP canister vent control valve
PBIB1026E
P0441 EVAP CONTROL SYSTEM
EC-283
< DTC/CIRCUIT DIAGNOSIS >
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
2.
Turn ignition switch ON.
3.
Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
Always perform test at a temperature of 5
°
C (41
°
F) or more.
>> GO TO 3.
3.
PERFORM DTC CONFIRMATION PROCEDURE-I
With CONSULT
1.
Start engine and warm it up to normal operating temperature.
2.
Turn ignition switch OFF and wait at least 10 seconds.
3.
Turn ignition switch ON.
4.
Turn ignition switch OFF and wait at least 10 seconds.
5.
Start engine and let it idle for at least 70 seconds.
6.
Select “PURG FLOW P0441” of “EVAPORATIVE SYSTEM” in “DTC WORK SUPPORT” mode with CON-
SULT.
7.
Touch “START”.
Is “COMPLETED” displayed on CONSULT screen?
YES
>> GO TO 5.
NO
>> GO TO 4.
4.
PERFORM DTC CONFIRMATION PROCEDURE-II
When the following conditions are met, “TESTING” will be displayed on the CONSULT screen. Maintain the
conditions continuously until “TESTING” changes to “COMPLETED”. (It will take at least 35 seconds.)
CAUTION:
Always drive vehicle at a safe speed.
If “TESTING” does not change for a long time, retry from step 2.
Is “COMPLETED” displayed on CONSULT screen?
YES
>> GO TO 5.
NO
>> Perform DTC CONFIRMATION PROCEDURE again. GO TO 3.
5.
PERFORM DTC CONFIRMATION PROCEDURE-III
Touch “SELF-DIAG RESULTS”.
Which is displayed on CONSULT screen?
OK
>> INSPECTION END
NG
>> Proceed to
.
6.
PERFORM COMPONENT FUNCTION CHECK
Perform component function check. Refer to
EC-283, "Component Function Check"
.
NOTE:
Use component function check to check the overall monitoring function of the EVAP control system purge flow
monitoring. During this check, a 1st trip DTC might not be confirmed.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Proceed to
.
Component Function Check
INFOID:0000000009651123
1.
PERFORM COMPONENT FUNCTION CHECK
Without CONSULT
Selector lever
Suitable position
VHCL SPEED SE
32 - 120 km/h (20 - 75 mph)
ENG SPEED
500 - 3,000 rpm
B/FUEL SCHDL
1.3 - 9.0 msec
COOLAN TEMP/S
More than 0
°
C (32
°
F)
EC-284
< DTC/CIRCUIT DIAGNOSIS >
[VQ35DE]
P0441 EVAP CONTROL SYSTEM
1.
Lift up drive wheels.
2.
Start engine (VDC switch OFF) and warm it up to normal operating temperature.
3.
Turn ignition switch OFF, wait at least 10 seconds.
4.
Turn ignition switch ON.
5.
Turn ignition switch OFF, wait at least 10 seconds.
6.
Start engine and wait at least 70 seconds.
7.
Set voltmeter probes to ECM harness connector terminals under the following conditions.
8.
Check EVAP control system pressure sensor value at idle speed and note it.
9.
Establish and maintain the following conditions for at least 1 minute.
10. Verify that EVAP control system pressure sensor value stays 0.1 V less than the value at idle speed (mea-
sured at step 6) for at least 1 second.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Proceed to
.
Diagnosis Procedure
INFOID:0000000009651124
1.
CHECK EVAP CANISTER
1.
Turn ignition switch OFF.
2.
Check EVAP canister for cracks.
Is the inspection result normal?
YES-1 >> With CONSULT: GO TO 2.
YES-2 >> Without CONSULT: GO TO 3.
NO
>> Replace EVAP canister. Refer to
2.
CHECK PURGE FLOW
With CONSULT
1.
Disconnect vacuum hose connected to EVAP canister purge volume control solenoid valve at EVAP ser-
vice port and install vacuum gauge. For the location of EVAP service port, refer to
EMISSION SYSTEM : System Description"
2.
Start engine and let it idle.
3.
Select “PURG VOL C/V” in “ACTIVE TEST” mode with CONSULT.
4.
Touch “Qd” and “Qu” on CONSULT screen to adjust “PURG VOL C/V” opening and check vacuum exist-
ence.
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> GO TO 4.
ECM
Connector
+
–
Terminal
Terminal
E16
102
(EVAP control system pressure sensor signal)
112
(Sensor ground)
Air conditioner switch
ON
Head lamp switch
ON
Rear window defogger switch
ON
Engine speed
Approx. 3,000 rpm
Gear position
Any position other than P, N or R
PURG VOL C/V
Vacuum
100%
Existed
0%
Not existed
P0441 EVAP CONTROL SYSTEM
EC-285
< DTC/CIRCUIT DIAGNOSIS >
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
3.
CHECK PURGE FLOW
Without CONSULT
1.
Start engine and warm it up to normal operating temperature.
2.
Stop engine.
3.
Disconnect vacuum hose connected to EVAP canister purge volume control solenoid valve at EVAP ser-
vice port and install vacuum gauge. For the location of EVAP service port, refer to
EMISSION SYSTEM : System Description"
4.
Start engine and let it idle.
Do not depress accelerator pedal even slightly.
5.
Check vacuum gauge indication before 60 seconds pass after starting engine.
6.
Rev engine up to 2,000 rpm after 100 seconds pass after starting engine.
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> GO TO 4.
4.
CHECK EVAP PURGE LINE
1.
Turn ignition switch OFF.
2.
Check EVAP purge line for improper connection or disconnection.
Refer to
EC-49, "EVAPORATIVE EMISSION SYSTEM : System Description"
.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair EVAP purge line.
5.
CHECK EVAP PURGE HOSE AND PURGE PORT
1.
Disconnect purge hoses connected to EVAP service port A and
EVAP canister purge volume control solenoid valve B.
2.
Blow air into each hose and EVAP purge port C.
3.
Check that air flows freely.
Is the inspection result normal?
YES-1 >> With CONSULT: GO TO 6.
YES-2 >> Without CONSULT: GO TO 7.
NO
>> Repair or clean hoses and/or purge port.
6.
CHECK EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE
With CONSULT
1.
Start engine.
2.
Perform “PURG VOL C/V” in “ACTIVE TEST” mode with CONSULT. Check that engine speed varies
according to the valve opening.
Vacuum should not exist.
Vacuum should exist.
SEF367U
SEF368U
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст