Nissan Quest E52. Instruction — part 809
HEADLINING
INT-35
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
Removal and Installation
INFOID:0000000009650295
CAUTION:
• When removing, always use a remover tool that is made of plastic to prevent damage to the parts.
• Never damage the body.
REMOVAL
1.
Remove front pillar garnish. Refer to
INT-21, "FRONT PILLAR GARNISH : Removal and Installation"
2.
Disconnect harness connector (A) from headlining and harness
fixing clips.
3.
Remove map lamp assembly. Refer to
INL-67, "Removal and Installation"
4.
Disconnect harness connector (A), and then disengage harness
fixing clip.
5.
Remove sun visor assembly.
a.
Disengage sun visor cover fixing pawls using a remover tool (A),
and then remove sun visor cover.
b.
Remove sun visor fixing screws.
c.
Disconnect harness connector, and then remove sun visor assembly.
6.
Remove sun visor holder.
13. Sun visor cover LH
14. Front assist grip
15.
Roof console
16. Rear ventilator grille A LH
17. Second assist grip LH
18.
Rear ventilator grille B LH
19. Third assist grip LH
20. Seat belt finisher
21.
Dual lock fastener
22. Metal clip
23. Map lamp bracket
: Clip
: Pawl
: Metal clip
: Clip
JMJIA4908ZZ
: Clip
JMJIA4909ZZ
: Pawl
JMJIA4910ZZ
INT-36
< REMOVAL AND INSTALLATION >
HEADLINING
Rotate 90
°
. Remove toward vehicle dower.
7.
Remove all assist grips.
a.
Disengage pawl of assist grip clip (1) using a remover tool (A).
Slide assist grip clip forward and remove it.
b.
Slide assist grip (2) forward and remove it.
8.
Remove roof console. (with rear display)
a.
Disengage roof console fixing clips using a remover tool (A).
b.
Disconnect harness connector, and then remove roof console.
9.
Remove center pillar upper garnish. Refer to
INT-26, "CENTER PILLAR UPPER GARNISH : Removal
10. Remove roof side garnish. Refer to
INT-28, "ROOF SIDE GARNISH : Removal and Installation"
11. Disengage antenna feeder connector (A), (B), (C), and fixing bolt (D).
JMJIA4911ZZ
: Pawl
JMJIA4398ZZ
: Clip
JMJIA4912ZZ
Left side
Right side
: Pawl
: Vehicle front
JMJIA6212ZZ
HEADLINING
INT-37
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
12. Remove seat belt finisher.
Disengage seat belt finisher fixing clips using a remover tool (A),
and then remove seat belt finisher.
13. Disengage clips on the rear end of headlining.
14. Peel dual lock fastener (A).
15. Remove headlining assembly though the back door.
CAUTION:
• Two workers are required for removal in order to prevent
damage.
• Apply protective tape to the portion where contact may
occur during work.
• ever bend headlining when removing.
16. Remove the following parts after removing headlining assembly.
• Personal lamp assembly: Refer to
INL-77, "Removal and Installation"
.
• Rear A/C control (without rear display)
Automatic air conditioning: Refer to
HAC-144, "Removal and Installation"
: Clip
JMJIA4914ZZ
1.
Normal roof
2.
Normal roof with rear display
3.
Sunroof with rear display
A.
Dual lock fastener
JMJIA6213ZZ
JMJIA4916ZZ
INT-38
< REMOVAL AND INSTALLATION >
HEADLINING
Instruction air conditioning: Refer to
HAC-239, "Removal and Installation"
.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• When installing headlining, start by installing both sun visor holders and headlining clips in order to
keep the headlining in position.
• Never bend headlining when installing.
• When installing assist grip, install metal clip (1) to assist grip
clip (2), and then install to the vehicle body.
NOTE:
When removing assist grip clip, metal clip remains on body side.
JMJIA3623ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст