Nissan Quest E52. Instruction — part 1260
WT-24
< BASIC INSPECTION >
TIRE PRESSURE SENSOR ID REGISTRATION
2.
Drive the vehicle at a speed at more than 40 km/h (25 MPH) for 3 minutes or more, then perform the tire
pressure sensor ID registration procedure.
3.
After ID registration for all wheels is completed, press “END” to end ID registration.
4.
Adjust the tire pressures for all wheels to the specified value. Refer to
.
Is ID registrations for all wheels completed?
YES
>> ID registration END.
NO
>> Performs trouble-diagnosis of the Tire Pressure Monitoring System (TPMS).
Tire position
Tire pressure kPa (kg/cm
2
, psi)
Front LH
240 (2.4, 35)
Front RH
220 (2.2, 31)
Rear RH
200 (2.0, 29)
Rear LH
180 (1.8, 26)
ID registration position
CONSULT
Front LH
“Red”
↓
“Green”
Front RH
Rear RH
Rear LH
C1704, C1705, C1706, C1707 LOW TIRE PRESSURE
WT-25
< DTC/CIRCUIT DIAGNOSIS >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
DTC/CIRCUIT DIAGNOSIS
C1704, C1705, C1706, C1707 LOW TIRE PRESSURE
DTC Logic
INFOID:0000000009653431
DTC DETECTION LOGIC
*:189.6 kPa (1.9 kg/cm
2
, 27 psi) [Standard air pressure is for 240 kPa (2.4 kg/cm
2
,35 psi) vehicles.]
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION
With CONSULT
1.
Turn the ignition switch ON.
CAUTION:
Never start the engine.
2.
Check the tire pressure for all wheels and adjust to the specified value. Refer to
.
3.
Perform self-diagnosis for “AIR PRESSURE MONITOR”.
Is DTC “C1704”, “C1705”, “C1706”, or “C1707” detected?
YES
>> Proceed to
.
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009653432
1.
TIRE PRESSURE SENSOR ID REGISTRATION
Perform tire pressure sensor ID registration. Refer to
.
Is tire pressure sensor ID registration completed?
YES
>> GO TO 2.
NO
>> Replace applicable tire pressure sensor. Refer to
WT-48, "Removal and Installation"
2.
CHECK TIRE PRESSURE
Check the air pressure of all wheels. Refer to
.
CAUTION:
If the checked value is close to the standard, reduce the tire pressure, and then with the ignition
switch ON, adjust the tire pressure again so that it is within the standard.
Is the inspection result normal?
YES
>> Perform “DTC CONFIRMATION PROCEDURE” (self-diagnosis) again. Refer to
NO
>> After adjusting the air pressure, GO TO 3
3.
CHECK TIRE PRESSURE SIGNAL
With CONSULT
1.
Select “DATA MONITOR” in “AIR PRESSURE MONITOR” of “BCM”.
2.
Check that the tire pressures match the standard value.
DTC
Display Item
Malfunction detected condition
Possible causes
C1704
LOW PRESSURE FL
Front LH tire pressure drops to * kPa (* kg/cm
2
, * psi) or less.
Low tire pressure
C1705
LOW PRESSURE FR
Front RH tire pressure drops to * kPa (* kg/cm
2
, * psi) or less.
C1706
LOW PRESSURE RR
Rear RH tire pressure drops to * kPa (* kg/cm
2
, * psi) or less.
C1707
LOW PRESSURE RL
Rear LH tire pressure drops to * kPa (* kg/cm
2
, * psi) or less.
Monitor item
Displayed value
AIR PRESS FL
Approximately equal to the indication on tire gauge value for front LH tire
AIR PRESS FR
Approximately equal to the indication on tire gauge value for front RH tire
WT-26
< DTC/CIRCUIT DIAGNOSIS >
C1704, C1705, C1706, C1707 LOW TIRE PRESSURE
Is the inspection result normal?
YES
>> After erasing DTC record, INSPECTION END.
NO
>> Repair or replace error-detected parts.
AIR PRESS RR
Approximately equal to the indication on tire gauge value for rear RH tire
AIR PRESS RL
Approximately equal to the indication on tire gauge value for rear LH tire
Monitor item
Displayed value
C1708, C1709, C1710, C1711 TIRE PRESSURE SENSOR
WT-27
< DTC/CIRCUIT DIAGNOSIS >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
C1708, C1709, C1710, C1711 TIRE PRESSURE SENSOR
DTC Logic
INFOID:0000000009653433
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
TIRE PRESSURE SENSOR ID REGISTRATION
Perform tire pressure sensor ID registration. Refer to
.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION
With CONSULT
1.
Drive the vehicle at 40 km/h (25 MPH) or more for 10 minutes.
CAUTION:
Total time driving at a speed of 40 km/h (25 MPH) or more must be 10 minutes.
NOTE:
Avoid driving in area where radio wave cannot be transmitted/received.
2.
Stop the vehicle.
3.
Perform self-diagnosis for “AIR PRESSURE MONITOR” of “BCM”.
Is DTC “C1708”, “C1709”, “C1710” or “C1711” detected?
YES
>> Proceed to
.
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009653434
1.
CHECK TIRE PRESSURE SIGNAL
With CONSULT
1.
Select “DATA MONITOR” in “AIR PRESSURE MONITOR” of “BCM”.
2.
Check the values that are displayed for “AIR PRESS FL”, “AIR PRESS FR”, “AIR PRESS RR”, and “AIR
PRESS RL”.
Are all tire pressures displayed 0 kPa (psi)?
YES
>> GO TO 2.
NO
>> Replace applicable tire pressure sensor. Refer to
WT-48, "Removal and Installation"
2.
CHECK RECEIVER CIRCUIT
1.
Turn the ignition switch OFF.
2.
Remove 10A fuse (#10).
3.
Disconnect BCM harness connector and tire pressure receiver harness connector.
4.
Check the continuity between BCM harness connector and tire pressure receiver harness connector.
DTC
Display Item
Malfunction detected condition
Possible causes
C1708
[NO DATA] FL
Tire pressure data signal from the front LH wheel
tire pressure sensor cannot be detected.
• Harness or connector
(Tire pressure receiver, BCM)
• Tire pressure sensor ID regis-
tration incomplete
• Tire pressure sensor
• Tire pressure sensor battery
voltage
• Driving in area where radio
wave cannot be transmitted/re-
ceived.
C1709
[NO DATA] FR
Tire pressure data signal from the front RH wheel
tire pressure sensor cannot be detected.
C1710
[NO DATA] RR
Tire pressure data signal from the rear RH wheel
tire pressure sensor cannot be detected.
C1711
[NO DATA] RL
Tire pressure data signal from the rear LH wheel
tire pressure sensor cannot be detected.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст