Nissan Quest E52. Instruction — part 1259
WT-20
< BASIC INSPECTION >
DIAGNOSIS AND REPAIR WORK FLOW
BASIC INSPECTION
DIAGNOSIS AND REPAIR WORK FLOW
Work Flow
INFOID:0000000009653426
DETAILED FLOW
1.
COLLECT THE INFORMATION FROM THE CUSTOMER
It is also important to clarify customer concerns before starting the inspection. Reproduce the symptom, and
understand it fully. Interview the customer about the concerns carefully. In some cases, it is necessary to
check the symptoms by driving the vehicle with the customer.
CAUTION:
Customers are not professionals. Never assume“maybe the customer means...” or “maybe the cus-
tomer mentioned this symptom.
>> GO TO 2.
2.
BASIC INSPECTION
1.
Turn the ignition switch ON.
CAUTION:
Never start the engine.
2.
Check the tire pressure for all wheels and adjust to the specified value. Refer to
.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Inspect or repair the tires or wheels.
3.
CHECK LOW TIRE PRESSURE WARNING LAMP
Check low tire pressure warning lamp display.
Does not low tire pressure warning lamp turn OFF?
YES
>> GO TO 4.
NO
>> GO TO 8.
4.
PERFORM SELF-DIAGNOSIS
With CONSULT
Perform “SELF-DIAG RESULTS”.
Is any DTC detected?
YES
>> Record or print DTC and freeze frame data (FFD). GO TO 5.
NO
>> GO TO 7.
5.
RECHECK THE SYMPTOM
With CONSULT
Perform “DTC CONFIRMATION PROCEDURE” with recorded DTC.
If two or more DTCs are detected, refer to
and determine trouble diagnosis order.
Is any DTC detected?
YES
>> GO TO 6.
NO
>> GO TO 7.
6.
REPAIR OR REPLACE ERROR-DETECTED PART
• Repair or replace error-detected parts.
• Reconnect part or connector after repairing or replacing.
• When DTC is detected, erase self-diagnostic result in “AIR PRESSURE MONITOR” of “BCM”.
>> GO TO 9.
7.
CRUISE FOR SYMPTOM CHECK
DIAGNOSIS AND REPAIR WORK FLOW
WT-21
< BASIC INSPECTION >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
1.
Start the engine.
2.
Drive for 10 minutes at a speed of 40 km/h (25 MPH) or more, then stop the vehicle.
CAUTION:
Total time driving at a speed of 40 km/h (25 MPH) or more must be 10 minutes.
>> GO TO 8.
8.
IDENTIFY ERROR-DETECTED SYSTEM BY SYMPTOM DIAGNOSIS
Estimate error-detected system based on symptom diagnosis.
>> GO TO 10.
9.
FINAL CHECK (WHEN DTC WAS DETECTED)
With CONSULT
Perform “DTC CONFIRMATION PROCEDURE” with displayed DTC.
Is any DTC detected?
YES
>> GO TO 6.
NO
>> INSPECTION END
10.
FINAL CHECK (WHEN SYMPTOM OCCURRED)
Make sure that the symptom is not detected.
Does symptom remain?
YES
>> GO TO 8.
NO
>> INSPECTION END
WT-22
< BASIC INSPECTION >
ADDITIONAL SERVICE WHEN REPLACING BCM
ADDITIONAL SERVICE WHEN REPLACING BCM
Description
INFOID:0000000009653427
When replacing BCM, tire pressure sensor ID registration is required.
Work Procedure
INFOID:0000000009653428
1.
PERFORM TIRE PRESSURE SENSOR ID REGISTRATION
Perform tire pressure sensor ID registration.
>> Refer to
TIRE PRESSURE SENSOR ID REGISTRATION
WT-23
< BASIC INSPECTION >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
TIRE PRESSURE SENSOR ID REGISTRATION
Description
INFOID:0000000009653429
This procedure must be done after replacing or rotating wheels, replacing tire pressure sensor or BCM.
Work Procedure
INFOID:0000000009653430
1.
TIRE PRESSURE SENSOR ID REGISTRATION PROCEDURE
CAUTION:
To perform ID registration, observe the following points:
• Never register ID in a place where radio waves are interfered (e.g. radio tower).
• Never register ID in a place close to vehicles including TPMS.
With CONSULT
1.
Display the “WORK SUPPORT” screen and select “ID REGIST”.
Is the tire pressure sensor activation tool (J-45295) used for the tire pressure sensor ID registration proce-
dure?
YES
>> GO TO 2.
NO
>> GO TO 3.
2.
TIRE PRESSURE SENSOR ID REGISTRATION PROCEDURE (WITH TIRE PRESSURE SENSOR ACTI-
VATION TOOL)
1.
Turn the ignition switch ON.
2.
Select the start button on the “ID REGIST” screen.
3.
Contact the tire pressure sensor activation tool (J-45295) (1) to
the side of the tire at the location to the tire pressure sensor.
4.
Press and hold the tire pressure sensor activation tool button
while pushing the tool to the tire surface. (approximately for 5
seconds)
CAUTION:
Perform the ID registration procedure starting from the
vehicle front left wheel, then repeat the procedure in the
order of the front right wheel, rear right wheel, and rear left
wheel.
5.
When ID registration is completed, check the following pattern at each wheel.
6.
After the ID registration procedure for all wheels is completed, press “END” to end ID registration, and
check that ID registration for all wheels is completed.
Is the check result normal?
YES
>> ID registration END.
NO
>> Refer to
3.
TIRE PRESSURE SENSOR ID REGISTRATION PROCEDURE (WITHOUT TIRE PRESSURE SENSOR
ACTIVATION TOOL)
1.
Adjust the tire pressure for all wheels to match the list below.
NNEIC0020ZZ
Sequence
ID registration position
Turn signal lamp
CONSULT
1
Front left wheel
2 blinks
“Red”
↓
“Green”
2
Front right wheel
3
Rear right wheel
4
Rear left wheel
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст