Nissan Quest E52. Instruction — part 673
FAX-20
< REMOVAL AND INSTALLATION >
FRONT DRIVE SHAFT
6.
Remove cotter pin, and then loosen wheel hub lock nut. Refer to
FAX-9, "Removal and Installation"
.
7.
Patch wheel hub lock nut with a piece of wood. Hammer the
wood to disengage wheel hub assembly from drive shaft.
NOTE:
Use suitable puller, if wheel hub assembly and drive shaft can-
not be separated even after performing the above procedure.
8.
Remove wheel hub lock nut. Refer to
.
9.
Remove strut assembly from steering knuckle. Refer to
10. Remove drive shaft from wheel hub assembly.
CAUTION:
• Never place drive shaft joint at an extreme angle. Also be
careful not to overextend slide joint.
• Never allow drive shaft to hang down without support for joint sub-assembly, shaft and the other
parts.
11. Remove splash guard. Refer to
12. Remove bearing housing mounting bolts.
13. Remove drive shaft assembly from transaxle assembly.
CAUTION:
Never place drive shaft joint at an extreme angle when
removing drive shaft. Also be careful not to overextend
slide joint.
14. Remove heat insulator from front suspension member.
15. Remove front exhaust tube. Refer to
.
16. Remove three way catalyst (bank 1) and heated oxygen sensor
harness bracket. Refer to
EM-33, "Removal and Installation"
17. Remove support bearing bracket.
18. Perform inspection after removal. Refer to
.
INSTALLATION
Note the following, and install in the reverse order of removal.
Transaxle Side
• Always replace transaxle side oil seal with new one when installing drive shaft. Refer to
• Place the protector (A) [SST: KV38107900 (
—
)] onto transaxle
assembly to prevent damage to the oil seal while inserting drive
shaft. Slide drive shaft sliding joint and tap with a hammer to install
securely.
• Install support bearing bracket in following procedure.
JPDIG0070ZZ
JSDIA2709ZZ
JPDIF0049ZZ
FRONT DRIVE SHAFT
FAX-21
< REMOVAL AND INSTALLATION >
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
- Temporarily tighten support bearing bracket (1) mounting bolts (A),
then tighten them to specified torque.
- Insert drive shaft into transaxle assembly, temporarily tighten bear-
ing housing (1) mounting bolts (A), then tighten them to specified
torque.
• Perform inspection after installation. Refer to
Wheel Hub Side
• Clean the matching surface of wheel hub lock nut and wheel hub assembly.
CAUTION:
Never apply lubricating oil to these matching surface.
• Clean the matching surface of drive shaft and wheel hub assembly.
And then apply paste [service parts (440037S000)] to surface (A)
of joint sub-assembly of drive shaft.
CAUTION:
Apply paste to cover entire flat surface of joint sub-assembly
of drive shaft.
• Use the following torque range for tightening the wheel hub lock
nut.
CAUTION:
• Since the drive shaft is assembled by press-fitting, use the tightening torque range for the wheel
hub lock nut.
• Be sure to use torque wrench to tighten the wheel hub lock nut. Never use a power tool.
• Never reuse wheel hub lock nut.
NOTE:
Wheel hub lock nut tightening torque does not over torque for avoiding axle noise, and does not less than
torque for avoiding looseness.
• Align the matching marks that have been made during removal when reusing the disc rotor.
• When installing a cotter pin, securely bend the basal portion to prevent rattles.
CAUTION:
• Never reuse cotter pin.
• Bend cotter pin at the root sufficiently to prevent any looseness.
• Perform the final tightening of each of parts under unladen conditions, which were removed when removing
suspension component.
• Perform inspection after installation. Refer to
.
WHEEL SIDE
JSDIA2710ZZ
JSDIA2711ZZ
Amount paste
: 1.0 – 3.0 g (0.04 – 0.10 oz)
: 206 – 211 N·m (21.1 – 21.5 kg-m, 152 – 155 ft-lb)
JPDIG0122ZZ
FAX-22
< REMOVAL AND INSTALLATION >
FRONT DRIVE SHAFT
WHEEL SIDE : Disassembly and Assembly
INFOID:0000000009651674
DISASSEMBLY
1.
Fix shaft of housing assembly with a vise.
CAUTION:
Protect shaft when fixing with a vise using aluminum or copper plates.
2.
Remove boot bands, and then remove boot from joint sub-assembly.
3.
Screw drive shaft puller (A) (commercial service tool) into joint
sub-assembly screw part to a length of 30 mm (1.18 in) or more.
Support drive shaft with one hand and pull out joint sub-assem-
bly from shaft.
CAUTION:
• Align drive shaft puller and drive shaft and remove them
by pulling firmly and uniformly.
• If joint sub-assembly cannot be removed after five or
more unsuccessful attempts, replace shaft and joint sub
assembly as a set.
4.
Remove circular clip from shaft.
5.
Remove boot from shaft.
6.
Perform inspection after disassembly. Refer to
ASSEMBLY
1.
Clean the old grease on joint sub-assembly with paper waste.
2.
Fill serration slot joint sub-assembly (1) with NISSAN genuine
grease or equivalent until the serration slot and ball groove
become full to the brim.
CAUTION:
After applying grease, use a paper waste to wipe off old
grease that has oozed out.
3.
Install boot and boot bands to shaft of housing assembly.
CAUTION:
• Wrap serration on shaft with tape (A) to protect the boot
from damage.
• Never reuse boot and boot band.
4.
Remove the tape wrapped around the serration on shaft.
JPDIG0151ZZ
JPDIF0008ZZ
JPDIF0009ZZ
FRONT DRIVE SHAFT
FAX-23
< REMOVAL AND INSTALLATION >
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
5.
Position the circular clip (1) on groove at the shaft edge.
CAUTION:
Never reuse circular clip.
NOTE:
Drive joint inserter is recommended when installing circular clip.
6.
Align both center axles of the shaft edge and joint sub-assembly.
Then assemble shaft with joint sub-assembly holding circular
clip.
7.
Install joint sub-assembly to shaft using plastic hammer.
CAUTION:
• Check circular clip is properly positioned on groove of the
joint sub-assembly.
• Confirm that joint sub-assembly is correctly engaged
while rotating drive shaft.
8.
Apply the specified amount of grease into the boot inside from
large diameter side of boot.
9.
Install the boot securely into grooves (indicated by “*” marks)
shown in the figure.
CAUTION:
If grease adheres to the boot mounting surface (indicated
by “*” marks) on the shaft or joint sub-assembly, boot may
be removed. Remove all grease from the boot mounting
surface.
10. To prevent the deformation of the boot, adjust the boot installa-
tion length to the specified value shown below by inserting the
suitable tool into inside of the boot from the large diameter side
of the boot and discharging the inside air.
CAUTION:
• If the boot installation length exceeds the standard, it may cause breakage of the boot.
• Be careful not to touch the inside of the boot with a tip of tool.
11. Secure the large and small ends of the boot with boot bands
using the boot band crimping tool (A) [SST: KV40107300 (
—
)].
CAUTION:
• Never reuse boot band.
JPDIF0305ZZ
Grease amount
: Refer to
.
RAC0049D
L
: Boot installation length
Boot installation length
: Refer to
.
JPDIF0222ZZ
JPDIF0012ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст