Nissan Quest E52. Instruction — part 671
FAX-12
< REMOVAL AND INSTALLATION >
FRONT DRIVE SHAFT BOOT
FRONT DRIVE SHAFT BOOT
Exploded View
INFOID:0000000009651667
LEFT SIDE
RIGHT SIDE
1.
Circular clip
2.
Dust shield
3.
Housing assembly
4.
Boot band
5.
Boot
6.
Damper band
7.
Dynamic damper
8.
Circular clip
9.
Joint sub-assembly
: Wheel side
: Always replace after every disassembly.
1: Fill NISSAN Genuine grease or equivalent.
2: Apply paste [service parts (440037S000)].
JPDIF0242ZZ
1.
Joint sub-assembly
2.
Circular clip
3.
Boot band
4.
Boot
5.
Housing assembly
6.
Dust shield
7.
Snap ring
8.
Support bearing
9.
Bearing housing
10. Support bearing bracket
JSDIA2706GB
FRONT DRIVE SHAFT BOOT
FAX-13
< REMOVAL AND INSTALLATION >
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
WHEEL SIDE
WHEEL SIDE : Removal and Installation
INFOID:0000000009651668
REMOVAL
1.
Remove tires with power tool. Refer to
.
2.
Remove wheel sensor. Refer to
BRC-119, "FRONT WHEEL SENSOR : Removal and Installation"
.
3.
Remove lock plate from strut assembly. Refer to
BR-20, "FRONT : Exploded View"
.
4.
Remove caliper assembly. Hang caliper assembly not to interfere with work. Refer to
CALIPER ASSEMBLY : Removal and Installation"
.
CAUTION:
Never depress brake pedal while brake caliper is removed.
5.
Remove disc rotor. Refer to
FAX-9, "Removal and Installation"
6.
Remove cotter pin, and then loosen wheel hub lock nut. Refer to
FAX-9, "Removal and Installation"
.
7.
Patch wheel hub lock nut with a piece of wood. Hammer the
wood to disengage wheel hub assembly from drive shaft.
NOTE:
Use suitable puller, if wheel hub assembly and drive shaft can-
not be separated even after performing the above procedure.
8.
Remove wheel hub lock nut. Refer to
.
9.
Remove strut assembly from steering knuckle. Refer to
10. Remove drive shaft from wheel hub assembly.
CAUTION:
• Never place drive shaft joint at an extreme angle. Also be
careful not to overextend slide joint.
• Never allow drive shaft to hang down without support for joint sub-assembly, shaft and the other
parts.
11. Remove boot bands, and then remove boot from joint sub-assembly.
12. Screw drive shaft puller (A) (commercial service tool) into joint
sub-assembly screw part to a length of 30 mm (1.18 in) or more.
Support drive shaft with one hand and pull out joint sub-assem-
bly from housing assembly.
CAUTION:
• Align drive shaft puller and drive shaft and remove them
by pulling firmly and uniformly.
• If joint sub-assembly cannot be pulled out, try after
removing drive shaft from vehicle.
: Wheel side
: N·m (kg-m, ft-lb)
: Always replace after every disassembly.
1: Fill NISSAN Genuine grease or equivalent.
2: Apply paste [service parts (440037S000)].
JPDIG0070ZZ
JPDIF0258ZZ
FAX-14
< REMOVAL AND INSTALLATION >
FRONT DRIVE SHAFT BOOT
13. Remove circular clip (1) from shaft of housing assembly.
14. Remove boot from shaft.
INSTALLATION
1.
Clean the old grease on joint sub-assembly with paper waste.
2.
Fill serration slot joint sub-assembly (1) with NISSAN genuine
grease or equivalent until the serration slot and ball groove
become full to the brim.
CAUTION:
After applying grease, use a paper waste to wipe off old
grease that has oozed out.
3.
Install boot and boot bands to shaft of housing assembly.
CAUTION:
• Wrap serration on shaft with tape to protect the boot from
damage.
• Never reuse boot and boot band.
4.
Remove the tape wrapped around the serration on shaft.
5.
Position the circular clip (1) on groove at the shaft edge.
CAUTION:
Never reuse circular clip.
NOTE:
Drive joint inserter is recommended when installing circular clip.
6.
Align both center axles of the shaft edge and joint sub-assembly.
Then assemble shaft with joint sub-assembly holding circular
clip.
7.
Install joint sub-assembly (1) to shaft using plastic hammer.
CAUTION:
• Check circular clip is properly positioned on groove of the
joint sub-assembly.
• Confirm that joint sub-assembly is correctly engaged
while rotating drive shaft.
8.
Apply the specified amount of grease into the boot inside from
large diameter side of boot.
JPDIF0007ZZ
JPDIF0008ZZ
JPDIF0007ZZ
Grease amount
: Refer to
.
JPDIF0011ZZ
FRONT DRIVE SHAFT BOOT
FAX-15
< REMOVAL AND INSTALLATION >
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
9.
Install the boot securely into grooves (indicated by “*” marks)
shown in the figure.
CAUTION:
If grease adheres to the boot mounting surface (indicated
by “*” marks) on the shaft or joint sub-assembly, boot may
be removed. Remove all grease from the boot mounting
surface.
10. To prevent the deformation of the boot, adjust the boot installa-
tion length to the specified value shown below by inserting the
suitable tool into inside of the boot from the large diameter side
of the boot and discharging the inside air.
CAUTION:
• If the boot installation length exceeds the standard, it may cause breakage of the boot.
• Be careful not to touch the inside of the boot with a tip of tool.
11. Secure the large and small ends of the boot with boot bands
using the boot band crimping tool (A) [SST: KV40107300 (
—
)].
CAUTION:
• Never reuse boot band.
• Secure boot band so that dimension (A) meets the specifi-
cation as shown in the figure.
12. Check that displacement does not occur when boot is rotated
with the joint sub-assembly and shaft of housing assembly fixed.
CAUTION:
• Reinstall them using boot bands when boot installation
positions become incorrect.
• Never reuse boot band.
13. Clean the matching surface of wheel hub lock nut and wheel
hub assembly.
CAUTION:
Never apply lubricating oil to these matching surface.
14. Clean the matching surface of drive shaft, wheel hub assembly.
And then apply paste [service parts (440037S000)] to surface
(A) of joint sub-assembly of drive shaft.
CAUTION:
Apply paste to cover entire flat surface of joint sub-assem-
bly of drive shaft.
15. Insert drive shaft to wheel hub assembly, and then temporarily
tighten wheel hub lock nut.
CAUTION:
Be sure to use torque wrench to tighten the wheel hub lock nut. Never use a power tool.
L
: Boot installation length
Boot installation length
: Refer to
.
JPDIF0222ZZ
JPDIF0012ZZ
A
: 7.0 mm (0.276 in) or less.
Amount paste
: 1.0 – 3.0 g (0.04 – 0.10 oz)
JPDIF0268ZZ
JPDIG0122ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст