Nissan Quest E52. Instruction — part 883
MA-28
< PERIODIC MAINTENANCE >
CHASSIS MAINTENANCE
POWER STEERING FLUID AND LINES : Inspection
INFOID:0000000009651647
Check fluid level in reservoir tank with engine off.
Use “HOT” range at fluid temperatures of 50 to 80
°
C (122 to 176
°
F)
or “COLD” range at fluid temperatures of 0 to 30
°
C (32 to 86
°
F).
CAUTION:
• Do not overfill.
• Recommended fluid is Genuine NISSAN E-PSF or equivalent.
Refer to
MA-10, "Fluids and Lubricants"
.
• Check lines for improper attachment, leaks, cracks, damage,
loose connections, chafing and deterioration.
• Check rack boots for accumulation of power steering fluid.
AXLE AND SUSPENSION PARTS
AXLE AND SUSPENSION PARTS : Inspection
INFOID:0000000009651648
Check front and rear axle and suspension parts for excessive play,
cracks, wear or other damage.
• Shake each wheel to check for excessive play.
• Check wheel bearings for smooth operation.
• Check axle and suspension nuts and bolts for looseness.
• Check strut (shock absorber) for oil leakage or other damage.
• Check suspension ball joint for grease leakage and ball joint dust
cover for cracks or other damage.
DRIVE SHAFT
SST850C
SST851C
SMA525A
JPPIA0011ZZ
CHASSIS MAINTENANCE
MA-29
< PERIODIC MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
DRIVE SHAFT : Inspection
INFOID:0000000009651649
Check boot and drive shaft for cracks, wear, damage and grease
leakage.
SFA108A
MA-30
< PERIODIC MAINTENANCE >
BODY MAINTENANCE
BODY MAINTENANCE
LOCKS, HINGES AND HOOD LATCH
LOCKS, HINGES AND HOOD LATCH : Lubricating
INFOID:0000000009651650
For hood and hood lock illustration.
• Hood: Refer to
• Hood lock: Refer to
.
For door and door lock illustration.
• Front door: Refer to
• Front door lock: Refer to
.
• Slide door: Refer to
• Slide door lock: Refer to
.
For back door and back door lock illustration.
• Back door: Refer to
• Back door lock: Refer to
.
SEAT BELT, BUCKLES, RETRACTORS, ANCHORS AND ADJUSTERS
SEAT BELT, BUCKLES, RETRACTORS, ANCHORS AND ADJUSTERS : Inspection
INFOID:0000000009651651
For front seat belt illustration. Refer to
For second seat belt illustration. Refer to
For third seat belt illustration. Refer to
.
CAUTION:
• After any collision, inspect all seat belt assemblies, including retractors and other attached hard-
wares (I.e. anchor bolt, guide rail set). Nissan recommends to replace all seat belt assemblies in use
during a collision, unless not damaged and properly operating after minor collision.
Also inspect seat belt assemblies not in use during a collision, and replace if damaged or improperly
operating.
Seat belt pre-tensioner should be replaced even if the seat belts are not in use during a frontal colli-
sion where the driver and passenger air bags are deployed.
• If any component of seat belt assembly is questionable, do not repair.
Replace as seat belt assembly.
• If webbing is cut, frayed, or damaged, replace belt assembly.
• Never oil tongue and buckle.
• Use a genuine NISSAN seat belt assembly.
For details, refer to
SB-6, "SEAT BELT RETRACTOR : Inspection"
SB-17, "SEAT BELT RETRACTOR : Inspection"
in SB section.
• Check anchors for loose mounting
• Check belts for damage
• Check retractor for smooth operation
• Check function of buckles and tongues when buckled and released
SERVICE DATA AND SPECIFICATIONS (SDS)
MA-31
< SERVICE DATA AND SPECIFICATIONS (SDS)
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
DRIVE BELT
DRIVE BELT : Drive Belt
INFOID:0000000009651652
DRIVE BELT
ENGINE COOLANT
ENGINE COOLANT : Periodical Maintenance Specification
INFOID:0000000009651653
ENGINE COOLANT CAPACITY (APPROXIMATE)
Unit:
(US qt, lmp qt)
ENGINE OIL
ENGINE OIL : Periodical Maintenance Specification
INFOID:0000000009651654
ENGINE OIL CAPACITY (APPROXIMATE)
Unit:
(US qt, lmp qt)
SPARK PLUG
SPARK PLUG : Spark Plug
INFOID:0000000009651655
SPARK PLUG
Unit: mm (in)
ROAD WHEEL
ROAD WHEEL : Road Wheel
INFOID:0000000009651656
ALUMINUM WHEEL
STEEL WHEEL
Tension of drive belt
Belt tension is not necessary, as it is automatically adjusted by drive belt auto-tensioner.
Engine coolant capacity (With reservoir tank at “MAX” level)
11.3 (12, 10)
Reservoir tank
0.75 (6/8, 5/8)
Drain and refill
With oil filter change
4.6 (4-7/8, 4)
Without oil filter change
4.3 (4-1/2, 3-3/4)
Dry engine (Overhaul)
5.3 (5-5/8, 4-5/8)
Make
DENSO
Standard type
FXE22HR11
Gap
Standard
1.1 (0.043)
Limit
1.4 (0.055)
Item
Limit
Runout
Axial runout
Less than 0.3 mm (0.012 in)
Radial runout
Allowable unbalance
Dynamic (At flange)
Less than 5 g (0.17 oz) (one side)
Static (At flange)
Less than 10 g (0.35 oz)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст