Nissan Quest E52. Instruction — part 882
MA-24
< PERIODIC MAINTENANCE >
CHASSIS MAINTENANCE
• When installing balance weight (1) to road wheels, set it into
the grooved area (A) on the inner wall of the road wheel as
shown in the figure so that the balance weight center (B) is
aligned with the tire balance machine indication position
(angle) (C).
CAUTION:
• Always use genuine NISSAN balance weights.
• Balance weights are non-reusable; always replace with
new ones.
• Never install three or more sheets of balance weight.
c.
If calculated balance weight value exceeds 50 g (1.76 oz), install
two balance weight sheets in line with each other as shown in
the figure.
CAUTION:
Never install one balance weight sheet on top of another.
3.
Start the tire balance machine again.
4.
Install drive-in balance weight on inner side of road wheel in the tire balance machine indication position
(angle).
CAUTION:
Never install three or more balance weight.
5.
Start the tire balance machine. Check that the inner and outer residual unbalance value is within the
allowable unbalance value.
CAUTION:
If either residual unbalance value exceeds limit, repeat installation procedures.
ADJUSTMENT (STEEL WHEEL)
Preparation Before Adjustment
Remove balance weight from the road wheel.
Wheel Balance Adjustment
• The details of the adjustment procedure are different for each model of wheel balancer. Therefore, refer to
each instruction instruction.
• If a tire balance machine has adhesion balance weight mode settings and drive-in weight mode setting,
select and adjust a drive-in weight mode suitable for steel wheels.
JPEIC0040ZZ
PEIA0033E
Allowable unbalance value
Dynamic (At flange)
: Refer to
.
Static (At flange)
: Refer to
.
CHASSIS MAINTENANCE
MA-25
< PERIODIC MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
1.
Set road wheel to wheel balancer, and then start wheel balancer.
2.
Install balance weight to road wheel according to the unbalance and position (angle) displayed on wheel
balancer.
CAUTION:
• Never install three or more balance weights on one side.
• Always use genuine NISSAN balance weights.
• Balance weights are non-reusable; always replace with new ones.
• Always use a plastic hammer when attaching the weight.
3.
Start the tire balance machine. Check that the inner and outer residual unbalance value is within the
allowable unbalance value.
CAUTION:
If either residual unbalance value exceeds limit, repeat installation procedures.
WHEELS : Tire Rotation
INFOID:0000000009651639
• Follow the maintenance schedule for tire rotation service intervals.
MA-4, "Explanation of General Maintenance"
.
• When installing the wheel, tighten wheel nuts to the specified
.
CAUTION:
• Never include the T-type spare tire when rotating the tires.
• When installing wheels, tighten them diagonally by dividing
the work two to three times in order to prevent the wheels
from developing any distortion.
• Be careful not to tighten wheel nut at torque exceeding the
criteria.
• Use NISSAN genuine wheel nut.
• Perform the ID registration, after tire rotation. Refer to
BRAKE FLUID LEVEL AND LEAKS
BRAKE FLUID LEVEL AND LEAKS : Inspection
INFOID:0000000009651640
• If fluid level is extremely low, check brake system for leaks.
BRAKE LINES AND CABLES
Allowable unbalance value
Dynamic (At flange)
: Refer to
.
Static (At flange)
: Refer to
.
SMA829C
SBR451D
MA-26
< PERIODIC MAINTENANCE >
CHASSIS MAINTENANCE
BRAKE LINES AND CABLES : Inspection
INFOID:0000000009651641
• Check brake fluid lines and parking brake cables for improper
attachment, leaks, chafing, abrasions, deterioration, etc.
BRAKE FLUID
BRAKE FLUID : Changing
INFOID:0000000009651642
1.
Drain brake fluid from each bleed valve.
2.
Refill until new brake fluid comes out from each bleed valve.
Use same procedure as in bleeding hydraulic system to refill
brake fluid.
Refer to
BR-11, "Bleeding Brake System"
• Refill with recommended Genuine NISSAN Super Heavy Duty
Brake Fluid or equivalent DOT 3 (US FMVSS No. 116).
Refer to
MA-10, "Fluids and Lubricants"
.
• Never reuse drained brake fluid.
• Be careful not to splash brake fluid on painted areas.
DISC BRAKE
DISC BRAKE : Inspection
INFOID:0000000009651643
DISC ROTOR
Check condition, wear, and damage.
CALIPER
• Check for leakage.
BRAKE PAD
SBR389C
SBR419C
SMA922A
CHASSIS MAINTENANCE
MA-27
< PERIODIC MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
• Check for wear or damage.
DISC BRAKE : Front Disc Brake
INFOID:0000000009651644
Unit: mm (in)
DISC BRAKE : Rear Disc Brake
INFOID:0000000009651645
Unit: mm (in)
STEERING GEAR AND LINKAGE
STEERING GEAR AND LINKAGE : Inspection
INFOID:0000000009651646
STEERING GEAR
• Check gear housing and boots for looseness, damage and grease
leakage.
• Check connection with steering column for looseness.
STEERING LINKAGE
Check ball joint, dust cover and other component parts for looseness, wear, damage and grease leakage.
POWER STEERING FLUID AND LINES
BRA0010D
Item
Limit
Brake pad
Wear thickness
2.0 (0.079)
Disc rotor
Wear thickness
26.0 (1.024)
Runout (with it attached to the vehicle)
0.040 (0.0016)
Item
Limit
Brake pad
Wear thickness
2.0 (0.079)
Disc rotor
Wear thickness
14.0 (0.551)
Runout (with it attached to the vehicle)
0.050 (0.0020)
SLIA0014E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст