Nissan Quest E52. Instruction — part 343
DLK-86
< SYSTEM DESCRIPTION >
SYSTEM (AUTOMATIC SLIDING DOOR SYSTEM)
*1
: When battery is reconnected, cancellation conditions are unconditionally fulfilled.
*2
: After returning to normal status, auto open/close function does not operate unless sliding door auto closure
function is operated.
INTERMITTENT CLUTCH FUNCTION
Display contents of CONSULT
Fail-safe
Reference page
*1
U1010: CAN COMM CIRCUIT
Intermittent clutch operation
Return to normal status
*2
B2401: IGN OPEN
When the following conditions are
fulfilled
• Sliding door control unit detects
that ignition switch is in the OFF
position
• Sliding door control unit detects
that ignition switch is not in the
ON position via CAN communica-
tion
B2402: TOUCH SENSOR OPEN
Return to normal status
B2403: PULSE ENCODER
Sliding door control unit detects that
sliding door is in the fully closed po-
sition
B2405: ECU FAIL
Erase DTC
*2
B2409: HALF LATCH SW
Sliding door control unit detects that
sliding door is in the fully closed po-
sition
B2412: ASD MTR/ENCDR
Sliding door control unit detects that
sliding door is in the fully closed po-
sition
B2413: ASD MTR/ENCDR
Sliding door control unit detects that
sliding door is in the fully closed po-
sition
B2414: ASD MTR TIME OUT
Sliding door control unit detects that
sliding door is in the fully closed po-
sition
B241A: ENCDR PWR SUPLY
When the following conditions are
fulfilled
• Return to normal status
• Sliding door control unit detects
that sliding door is in the fully
closed position
SYSTEM (AUTOMATIC SLIDING DOOR SYSTEM)
DLK-87
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
INTERMITTENT CLUTCH FUNCTION : System Description
INFOID:0000000009649006
SYSTEM DIAGRAM
*
: For automatic sliding door LH
• During automatic operation of sliding door, when the vehicle is on a slope, it may become impossible to con-
tinue automatic operation of sliding door and its operation may stop suddenly, or door may open or close
suddenly. This is due to automatic door main switch being turned the OFF position or any other cause. For
prevention purposes, sliding door control unit stops automatic sliding door motor, and simultaneously oper-
ates clutch intermittently and prevents sliding door from opening or closing suddenly, so that safety can be
secured.
• Intermittent clutch function operates when any of the following conditions is satisfied.
INTERMITTENT CLUTCH FUNCTION : Fail-safe
INFOID:0000000009649007
FAIL-SAFE CONTROL BT DTC
Sliding door control unit performs fail-safe control when any DTC is detected.
JMKIA8097GB
Operation
Operation condition
auto open/close function in operation
Fuel filler lid status: Closed
→
Open
Automatic sliding door system malfunction
Battery voltage: Continuous detection of 9 V or less for 2 seconds or more
Hold function in operation
Vehicle speed: 0 km/h
Fuel filler lid status: Closed
→
Open
Automatic sliding door system malfunction
Anti-pinch function
Continuous detection of pinching for 3 times during auto close operation
DLK-88
< SYSTEM DESCRIPTION >
SYSTEM (AUTOMATIC SLIDING DOOR SYSTEM)
*1
: When battery is reconnected, cancellation conditions are unconditionally fulfilled.
*2
: After returning to normal status, auto open/close function does not operate unless sliding door auto closure
function is operated.
BUZZER REMINDER FUNCTION
BUZZER REMINDER FUNCTION : System Description
INFOID:0000000009649008
• Automatic sliding door warning buzzer sounds when sliding door automatic function is operated as a
reminder.
Display contents of CONSULT
Fail-safe
Reference page
*1
U1010: CAN COMM CIRCUIT
Intermittent clutch operation
Return to normal status
*2
B2401: IGN OPEN
When the following conditions are
fulfilled
• Sliding door control unit detects
that ignition switch is in the OFF
position
• Sliding door control unit detects
that ignition switch is not in the
ON position via CAN communica-
tion
B2402: TOUCH SENSOR OPEN
Return to normal status
B2403: PULSE ENCODER
Sliding door control unit detects that
sliding door is in the fully closed po-
sition
B2405: ECU FAIL
Erase DTC
*2
B2409: HALF LATCH SW
Sliding door control unit detects that
sliding door is in the fully closed po-
sition
B2412: ASD MTR/ENCDR
Sliding door control unit detects that
sliding door is in the fully closed po-
sition
B2413: ASD MTR/ENCDR
Sliding door control unit detects that
sliding door is in the fully closed po-
sition
B2414: ASD MTR TIME OUT
Sliding door control unit detects that
sliding door is in the fully closed po-
sition
B241A: ENCDR PWR SUPLY
When the following conditions are
fulfilled
• Return to normal status
• Sliding door control unit detects
that sliding door is in the fully
closed position
Operation
Automatic sliding door warning buzzer
Auto open
2 times for start operation
Auto close
From sliding door halfway position until operation start of sliding door auto clo-
sure function
Power assist function (open)
2 times for start operation
Power assist function (close)
Reverse
2 times for reverse operation
SYSTEM (AUTOMATIC SLIDING DOOR SYSTEM)
DLK-89
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
• When all of the following conditions are satisfied, automatic sliding door warning buzzer sounds, alerting the
driver to stop the vehicle.
- Sliding door: Open status (Sliding door switch ON or full latch switch ON)
- Vehicle speed: 0 km/h or more
BUZZER REMINDER FUNCTION : Fail-safe
INFOID:0000000009649009
FAIL-SAFE CONTROL BT DTC
Sliding door control unit performs fail-safe control when any DTC is detected.
*1
: When battery is reconnected, cancellation conditions are unconditionally fulfilled.
Operation
Function
Automatic sliding door warning buzzer
operation pattern
Automatic operation start
Sliding door open/close switch
Sound twice (2 times)
Intelligent Key button operation
Power assist function
Reverse operation start
Reverse operation detection
Hold function in operation
Vehicle speed 0km/h or more, and sliding
door open
Sound continuously (until sliding door is
fully closed or the vehicle stops)
Auto close in operation
Auto close in operation
Continuously sounds intermittently (until
sliding door is in half latch position)
Display contents of CONSULT
Fail-safe
Reference page
*1
U1010: CAN COMM CIRCUIT
Intermittent clutch operation
Return to normal status
*2
B2401: IGN OPEN
When the following conditions are
fulfilled
• Sliding door control unit detects
that ignition switch is in the OFF
position
• Sliding door control unit detects
that ignition switch is not in the
ON position via CAN communica-
tion
B2402: TOUCH SENSOR OPEN
Return to normal status
B2403: PULSE ENCODER
Sliding door control unit detects that
sliding door is in the fully closed po-
sition
B2405: ECU FAIL
Erase DTC
*2
B2409: HALF LATCH SW
Sliding door control unit detects that
sliding door is in the fully closed po-
sition
B2412: ASD MTR/ENCDR
Sliding door control unit detects that
sliding door is in the fully closed po-
sition
B2413: ASD MTR/ENCDR
Sliding door control unit detects that
sliding door is in the fully closed po-
sition
B2414: ASD MTR TIME OUT
Sliding door control unit detects that
sliding door is in the fully closed po-
sition
B241A: ENCDR PWR SUPLY
When the following conditions are
fulfilled
• Return to normal status
• Sliding door control unit detects
that sliding door is in the fully
closed position
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст